Releases: eez-open/modular-psu-firmware
1.7.6
1.7.5
1.7.4
Note: this release is strongly recommended if the DCP405 module is used to charge batteries. With #9 (enabled by default) it will not be possible to enable power output with the battery connected. This feature will force you to first enable the output and only then connect the battery you want to charge.
- Fix for eez-open/dib-mio168-fw#5
- Auto-recall fix for DCP R3B2
- #9 Measure output voltage before output is switched on
- #255 Feature request: warning when enabling channel onto live battery
- #311 Rule for accepting a new ethernet connection and releasing the old one
- #312 OFF state current settings
- #313 Auto-recall info in log file
1.8 Alpha-2
- #274 EEZ flow Progress bar overflows
- #276 EEZ flow empty select causes restart of BB3
- #277 EEZ flow SCPI string has quotes
- #278 Writing a string to a variable doesn't work
- #279 EEZ flow comparison in switch not always working as expected
- #280 Text widget action generates a number, where integer is expected
- #285 EEZ flow: Button widgets don't always show updated text
- #286 EEZ flow start after displaying pinout page restarts BB3
- #289 EEZ flow in SCPI command reading a negative value stores wrong value
1.7.3
1.8 Alpha
This is the first pre-release that allows testing of EEZ Studio v0.9.87 debugger functionality.
Please note that various instabilities are possible, therefore it is not recommended to be used in production.
1.7.2
The firmware solves several issues with MIO168 and improves the operation of the encoder, which on some MCU modules could reverse the direction at higher rotation speeds.
1.7.1
This release introduces a custom bootloader that makes this and all future firmware download easier using EEZ Studio (v0.9.84 or newer).
1.7
A simple function generator has been added in this release (#198). The data logger (DLOG) can now work with multiple channels and supports the sampling rate of the MIO168 module as well as the addition of a bookmark. UART (DIN1 / DOUT1 pins on the front panel) now allows communication with other devices but also control of BB3 using SCPI commands (#19). Two additional protection mechanisms have been added for the DCP405 module (#195, #202).
- #19 SCPI via UART
- #20 Add support for timestamped text in DLOG
- #42 Add support for MIO168 module
- #45 Add support for PREL6 module
- #128 MQTT can't connect to broker without authentication
- #152 Checking the firmware target on the on-board MCU
- #155 Ambiguous error message about high temperature
- #156 Firmware download warning message
- #157 USB issue with OTG cable connected
- #164 DISP:TEXT doesn't display last character from the string
- #169 Feature Request: Option to hide recording status window
- #171 Clear DLOG REMark and X axis label when DLOG is started through GUI
- #174 Step menu allows negative delay setting with encoder
- #176 DLOG view doesn't remember settings
- #178 Dlog window at bottom of screen causes flashing at the top
- #180 Add hold delay on Lock display option
- #182 Set execution time for the route:close and route:open SCPI commands
- #183 The GUI Shutdown option does not turn off AC power
- #184 Pinout page
- #185 Add support for MUX14D module
- #188 Disable IRQ inputs for empty slots or modules in error state
- #191 DCM224: displaying current below zero
- #192 Calibration via GUI
- #194 Change various defaults
- #195 Down-programmer sinking limit
- #198 Programing LIST refactoring (i.e. function generator)
- #199 Generate Ethernet MAC address from MCU serial number
- #200 Change the User SW function if the channel outputs are in INHibit mode
- #202 Continuous checking of output voltage on DCP module
- #203 "Wrong thread 6" message when limit is set below set level via SCPI and GUI (volt or current) on DCP405
- #204 Display connection diagram for coupled DCP modules
- #205 CapReform fixes
- #206 Reorganizing the status bar
- #208 AUX temp sensor trip does not change color
- #209 Wrong calibration params displayed on DCM CH2
- #211 Remove all minimized views
- #219 Popup indication when changing the display view
- #221 Add indication of current range selection on DCP module
- #222 System trigger refactoring
- #223 OE on ramp adjustment
- #229 Add tolerance for OCP trip level
- #232 Full scale: Auto doesn't display YT-view correctly