release notes

RELEASE.txt

@@ -1,4 +1,4 @@
-SLS Detector Package Major Release 7.0.3 released on 10.11.2023
+SLS Detector Package Major Release 7.0.3 released on 13.11.2023
 ===============================================================
 
 This document describes the differences between v7.0.3 and v7.0.2   
@@ -22,32 +22,36 @@ This document describes the differences between v7.0.3 and v7.0.2
     Firmware
     --------
 
+
     *   [Eiger] Blocking trigger on quad
         Previously, blocking software trigger on a quad was not blocking. Fixed
         with firmware v32.
 
 
-
     Client
     ------
 
+
     *   Limit port number max to 65535
         Previously, one could set the port numbers (TCP, UDP, ZMQ) to values 
         higher than 65535 and also to 0. However, it was truncated to 16 bit
         in the background, but not relayed to the user. 
         Now, it will throw if it is 0 or greater than 65535 (16 bit).
 
+
     *   Stopping acqusition for a single or subset of modules
         The Detector API previously stopped all modules.
         Now, it takes into account which modules the user wanted to stop.
 
+
     *   [Jungfrau] Stop in sync mode
         When stopping acquisition in sync mode, only the master module sometimes 
         returns 'Idle' state instead of 'Stopped'. The software threw an 
         exception for the different states then.
         Now, it does not throw and a fix will be added to the next firmware 
         release for the different states (with SW release: v8.0.0).
 
+
     *   [Eiger] Incorrect error message in Stop
         When stopping acquisition, if a half module were to give an error in a 
         rare case while the others succeeded, this would result in an re-attempt 
@@ -57,38 +61,42 @@ This document describes the differences between v7.0.3 and v7.0.2
         immediately.
 
 
-
     Receiver
     --------
 
+
     *   Limit TCP port number (command line) to max of 65535
         Refer issue under 'Client'.
 
-
 
     Detector Simulator
     ------------------
 
+
     *   Limit TCP port number (command line) to max of 65535
         Refer issue under 'Client'.
 
+
     *   Some commands such as 'readnrows' would complain that it cannot be set 
         because the detector is not idle, but was setting it anyway. Fixed.
 
 
     Gui/ Client Callback
     --------------------
 
+
     *   [Jungfrau] Gui: corrected color map of gain plot
         Previously, color on the gain plot did not update after the first image, 
         unless there were x/y min/max changes or window resizing. Fixed.
 
+
     *   [Jungfrau] Acquisition finished callback error status in sync mode
         When stopping acquisition in multi module Jungfrau sync mode, 
         different status (master 'idle' and slaves 'stopped' in 
         firmware 2.4.1 or 1.4.1) show as 'error' in acquisition finished call 
         back (mainly used for gui). This is fixed.
 
+
     *   [Jungfrau] Gui: Next frame number shown as 0 for inconsistency
         When stopping an acquisition in a multi module Jungfrau, the next 
         frame numbers might be different, for which the Gui shows an error message
@@ -97,13 +105,14 @@ This document describes the differences between v7.0.3 and v7.0.2
         that 0 is an invalid input.
 
 
-
     Data Processing
     ---------------
 
+
     *   [Moench] Segmentation fault with moench03RawDataPrcess
         Previously, it crashed when nframes > 0. Fixed.
 
+
     *   [Moench] Moench interpolation issues fixed.
 
 
@@ -142,8 +151,8 @@ This document describes the differences between v7.0.3 and v7.0.2
 
     Eiger       02.10.2023 (v32)                    (updated in 7.0.3)
 
-    Jungfrau    16.05.2023 (v1.4.1, HW v1.0)        (updated in 7.0.3)
-                15.05.2023 (v2.4.1, HW v2.0)        (updated in 7.0.3)
+    Jungfrau    16.05.2023 (v1.4.1, HW v1.0)        (updated in 7.0.2)
+                15.05.2023 (v2.4.1, HW v2.0)        (updated in 7.0.2)
 
     Mythen3     24.01.2023 (v1.4)                   (updated in 7.0.0)