Skip to content

itay7564/ElectraWifi

 
 

Folders and files

NameName
Last commit message
Last commit date

Latest commit

 

History

30 Commits
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Repository files navigation

ElectraWifi

This project intends to replace a plain Electra AC IR receiver with an ESP8266 to give it wifi capabilities and control it over MQTT.

Description

The original receiver itself is "dumb" and doesn't hold any state and all the interaction is handled by the main unit, this makes it expandable so it can easily be replaced by an ESP8266.

The receiver is connected to the main unit with an 8-pin mini din connector, with the following pins:

  1. 5V
  2. Heat LED
  3. IR signal
  4. Green power LED (LOW for on)
  5. Timer LED
  6. Beep
  7. Button
  8. Cool LED

So now all we need to do is throw out the old receiver and hook up an ESP8266 to the pins 1, 3, 4.

Prerequisites

Hardware

First you would need:

  • ESP8266 (ESP32 would also work)
  • 1 NPN transistor
  • 2 1kΩ resistors
  • A breadboard/PCB
  • IR receiver (optional)

Hook everything up according to the following schematic:

To use the code as-is, use GPIO4 for IR send, GPIO5 for power state input and GPIO14 for IR recv (optional).

Software

The code in this repo is based on Homie for MQTT handling and for OTA. Please follow the instructions there to install all the dependencies.

Once the code is installed on the esp, it will boot in configuration mode. Follow the instructions here to upload a JSON configuration file.

A sample json config file is provided under /data/homie/config.json. This file can be edited and uploaded using platform.io under "Platform -> Build Filesystem Image" and the "Platform -> Upload Filesystem Image". Make sure to properly edit the file before uploading.

Building

Building with platform.io is quite simple. But Homie is not compatible with Platform.io 3.0 for ESP8266 out of the box. You need to change two files in the Homie library.

  • Start building as usual. You will see some errors regarding the "HTTPClient" calls not being supported.

  • Navigate to the ./pio/libdeps//Homie/src/Homie/Boot

  • Edit the BootConfig.hpp and BootConfig.cpp files as follows:

  • BootConfig.hpp Add the following line:

  WiFiClient _wifiClient;

So that the file looks as follows:

 private:
  AsyncWebServer _http;
  WiFiClient _wifiClient;
  HTTPClient _httpClient;
  DNSServer _dns;
  • BootConfig.cpp Replace the following line:
  _httpClient.begin(url);

so that it looks as follows:

  // send request to destination (as in incoming host header)
  _httpClient.setUserAgent(F("ESP8266-Homie"));
  _httpClient.begin(_wifiClient,url);
  // copy headers

Usage

After the esp is configured, it will subscribe to the following MQTT topics:

  • .../state/json/set
    • This topic accepts a json in the following format (all fields are mandatory), updates the state and send it to the AC unit:
      {"power": "on|off", "mode": "cool|heat|fan|dry|auto", "fan": "low|med|high|auto", "temperature": 15..30, "ifeel": "on|off", "swing":"on|off|hor|both"}
  • .../ifeel_temperature/state/set
    • This topic accepts a number between 5 and 36 and sends it to the main unit as a temperature received by the "i feel" function of the remote.

Monitoring and getting the real state of the AC is also possible by subscribing to the following topics:

  • .../power/state
  • .../mode/state
  • .../fan/state
  • .../temperature/state
  • .../ifeel/state
  • .../swing/state

Home Assistant

Home Assistant's MQTT HVAC component can be used with the following configuration:

climate:
  - platform: mqtt
    name: AC
    modes:
      - "heat"
      - "cool"
      - "dry"
      - "off"
    fan_modes:
      - "high"
      - "med"
      - "low"
      - "auto"
    swing_modes:
      - "off"
      - "on"
      - "hor"
      - "both"
    min_temp: 16
    max_temp: 30
    power_command_topic: "devices/AC/power/state/set"
    payload_on: "on"
    payload_off: "off"
    mode_command_topic: "devices/AC/mode/state/set"
    mode_state_topic: "devices/AC/mode/state"
    temperature_command_topic: "devices/AC/temperature/state/set"
    temperature_state_topic: "devices/AC/temperature/state"
    fan_mode_command_topic: "devices/AC/fan/state/set"
    fan_mode_state_topic: "devices/AC/fan/state"
    swing_mode_command_topic: "devices/AC/swing/state/set"
    swing_mode_state_topic: "devices/AC/swing/state"

It's possible to activate the iFeel by using the build-in aux-heat or away_mode topic for the MQTT HVAC component by adding the following lines: Its not ideal as it will show "Preset: Home/Away" but it works fine.

climate:
    ...
    ...
    away_mode_command_topic: "devices/AC/ifeel/state/set"
    away_mode_state_topic: "devices/AC/ifeel/state"

Home Assistant - Lovelace UI

Lovelace UI example:

Lovelace UI Example

Home Assistant's MQTT HVAC component can be used with the following configuration (note the use if simple-thermostat custom component):

cards:
  - type: custom:simple-thermostat
    entity: climate.ac
    name: false
    step_size: 1
    control:
      _headings: false
      hvac:
        'off':
          icon: mdi:power
          name: 'כבוי'
        cool:
          icon: mdi:snowflake
          name: 'קור'
        heat:
          icon: mdi:fire
          name: 'חימום'
        dry: false
      fan:
        'low':
          icon: mdi:network-strength-1
          name: 'נמוך'
        'med':
          icon: mdi:network-strength-3
          name: 'בינוני'
        'high':
          icon: mdi:network-strength-4
          name: 'גבוהה'
        'Auto':
          icon: mdi:autorenew
          name: 'אוטו'
      swing:
        'on':
          icon: mdi:home-thermometer
          name: 'iFeel פעיל'
        'off':
          icon: mdi:home-thermometer-outline
          name: 'iFeel כבוי'
    sensors:
      - entity: sensor.<external-hunidity-sensor>
        name: 'לחות'
      - entity: sensor.<external-temperature-sensor>
        name: 'טמפרטורה'
    hide:
      mode: false
      temperature: true

Home Assistant - iFeel update based to external sensor

To Inject external temperature (from any tempureture sensor) to iFeel every minute, add the following automation:

automation:
  - alias: Update ifeel temperature
    initial_state: 'on'
    trigger:
      platform: time_pattern
      minutes: "/1"
    action:
      service: mqtt.publish
      data:
        topic: "homie/<homie-id>/ifeel_temperature/state/set"
        payload_template: "{{ states.sensor.<my-tempereture-sensor>.state }}"

Credits

Many thanks to @barakwei and IRelectra for analyzing the IR protocol.

About

Control Electra AC with esp8266

Resources

License

Stars

Watchers

Forks

Releases

No releases published

Packages

No packages published

Languages

  • C++ 100.0%