This is a universal firmware that has been optimized and enhanced for both the Voxelab Aquila and Creality Ender-3 V2/S1.
This is based on MriscoC's Professional Firmware for the Creality Ender-3 V2/S1. This particular build release is for the LCD color displays of Creality Ender-3V2 or similar variant. If you are using a Voxelab brand printer, you can try the Aquila build here.

Recent Updates

EDITABLE_HOMING_FEEDRATE is now available in most, if not all, builds
BTT SKR Mini E3 V3 / V2 / V3.0.1 finally supported for ProUI - (4.3" Stock Aquila/Ender-3V2 Color LCD)

^{If you have a TFT or other display, you can request firmware *.bin files to be made, or compile your own}

BIQU MicroProbe V2.0 is now supported with _BMP prefix
Creality Spider Speedy Ceramic Hotend is now supported with _SPDY5 prefix
Creality E3 Free-runs + Ender-3 S1 | F1/F4 board support

Important

🚩To use this version, you must✶ update the DWIN_SET to the LCD screen. New ICON's have been added, and others were remastered.

Choose a DWIN_SET from the "display assets" folder
Copy it to the root of an SD card
Remove the name in ( ) from the folder
^{e.g. "DWIN_SET (Original)" => "DWIN_SET"}
Open the back of the LCD, insert the card📲
Turn on power, wait until the screen goes Blue🔵 to Red🔴
Turn off, remove card⤵. Good to go!✅

✶ Technically you don't have to reflash the new DWIN_SET, but some ICON's will be missing if you do not.

Warning

🚧Please be aware of the following:

⚠️Previous Gcode Preview Thumbnails Issue has been FIXED! Thank you @Nazar78 for your help.

While using _BLT or _MM versions, if you encounter the bed Mesh not saving...
This workaround resolves the issue without having to redo the mesh again.

Build Mesh (first time)
Save Mesh
After any time you Power Off and Power On -->
3a. Go to Control/Advanced Settings/Load Settings
-OR-
3b. Load this into your Start Gcode

G28 ; Home
M501 ; Load settings
M420 S1 ; Pull your mesh bed level
;(Remaining Gcode / Start Print)>>>

If you experience this issue as it starts printing --> Mesh leveling data is drawing over the printing screen
Go to Slicer Gcode Scripts

Note

⍰ The follow may apply to you if the mainboard chip supports 256KB max

Note ➀: Due to lack of flash memory space in the Aquila's GD32/N32|F103RCT6, some features had to be disabled in the ProUI of UBL and BLT versions, including, but not limited to:

Configuration.h

HOST_KEEPALIVE_FEATURE

^{Sends a busy status message to the host}

PREHEAT_2_LABEL

^'ABS'

PREHEAT_3_LABEL

^'Warmup'

G26_MESH_VALIDATION

^G26

NOZZLE_CLEAN_FEATURE

^{G12 P<#> S<#> T<#>}

HAS_LOCKSCREEN

^{Simple lockscreen}

ACTIVATE_MESH_ITEM

^{Active Mesh Leveling menu option}

Configuration_adv.h

POWER_LOSS_RECOVERY

^{Continue Print after Power-Loss}

M114_DETAIL

^{Use 'M114' for details to check planner calculations}

CANCEL_OBJECTS

^{Use 'M486' to allow Marlin to skip objects}

AUTO_REPORT_POSITION

^{M154 S<seconds>}

EXTENDED_CAPABILITIES_REPORT

M115_GEOMETRY_REPORT

^{'M115' outputs Firmware Capabilities (enabled features)}

REALTIME_REPORTING_COMMANDS

^{Report position and state of the machine}

Note ➁: The latest releases are promoting UBL versions over ABL (BLT - BL Touch), but ABL/BLT versions will be available. MPC autotune is available for the hot-end as a replacement to PID autotune.

📚Versions

These are the configurations offered:

Bed Leveling Options

[ _Default-NP ]: Use if you have a near stock machine

^{Default No Probe}

[ _MM ]: Create a bed mesh without an auto bed probe

^{Manual Mesh Bed Leveling}

[ _BLT ]: Use if you have a CR/3D/BL-Touch level sensor installed.

^{Bilinear Auto Bed Leveling}

[ _UBL ]: Similar to both MM and BLT - with more options. Recommended over BLT

^{Unified Bed Leveling}

Special Versions

^{(List of file prefixes and suffixes)}

[ -ProUI-EX ]
| ProUI Extra Features |
Toolbar, change bed physical dimensions, and other special features and options

Contributors

gcardoso22, Nazar78, and wlkmanist

Assets 66

20 Nov 06:55

classicrocker883

2.1.3f-11-ender3-1

84ef752

Ender-3V2 Build for November Rev.1

NOVEMBER 2024 Rev.1

Version: 2.1.3f-11-ender3-1

Continually updating with Marlin bugfix-2.1.x

_{⬂ List of recent updates ⬃}

^{What's new in this release}

⍟ Firmware Selector ⍟

Tip

You can use the Firmware Selector to help choose which file to download.

How to install the firmware

To update the firmware, choose the file ending in .bin and place it in your SD card:

^{(You may need to rename the file if reinstalling or if it doesn't flash the first time)}

For a Creality board, put it in the root folder of the drive
^{Or unless otherwise specified}

If you have not yet updated your LCD (since: November Rev.1),

please flash the new DWIN_SET now!

Recent Updates

EDITABLE_HOMING_FEEDRATE is now available in most, if not all, builds
BTT SKR Mini E3 V3 / V2 / V3.0.1 finally supported for ProUI - (4.3" Stock Aquila/Ender-3V2 Color LCD)

^{If you have a TFT or other display, you can request firmware *.bin files to be made, or compile your own}

BIQU MicroProbe V2.0 is now supported with _BMP prefix
Creality E3 Free-runs + Ender-3 S1 | F1/F4 board support

Important

🚩To use this version, you must✶ update the DWIN_SET to the LCD screen. New ICON's have been added, and others were remastered.

Choose a DWIN_SET from the "display assets" folder
Copy it to the root of an SD card
Remove the name in ( ) from the folder
^{e.g. "DWIN_SET (Original)" => "DWIN_SET"}
Open the back of the LCD, insert the card📲
Turn on power, wait until the screen goes Blue🔵 to Red🔴
Turn off, remove card⤵. Good to go!✅

✶ Technically you don't have to reflash the new DWIN_SET, but some ICON's will be missing if you do not.

Warning

🚧Please be aware of the following:

⚠️Previous Gcode Preview Thumbnails Issue has been FIXED! Thank you @Nazar78 for your help.

While using _BLT or _MM versions, if you encounter the bed Mesh not saving...
This workaround resolves the issue without having to redo the mesh again.

Build Mesh (first time)
Save Mesh
After any time you Power Off and Power On -->
3a. Go to Control/Advanced Settings/Load Settings
-OR-
3b. Load this into your Start Gcode

G28 ; Home
M501 ; Load settings
M420 S1 ; Pull your mesh bed level
;(Remaining Gcode / Start Print)>>>

If you experience this issue as it starts printing --> Mesh leveling data is drawing over the printing screen
Go to Slicer Gcode Scripts

Note

⍰ The follow may apply to you if the mainboard chip supports 256KB max

Note ➀: Due to lack of flash memory space in the Aquila's GD32/N32|F103RCT6, some features had to be disabled in the ProUI of UBL and BLT versions, including, but not limited to:

Configuration.h

HOST_KEEPALIVE_FEATURE

^{Sends a busy status message to the host}

PREHEAT_2_LABEL

^'ABS'

PREHEAT_3_LABEL

^'Warmup'

G26_MESH_VALIDATION

^G26

NOZZLE_CLEAN_FEATURE

^{G12 P<#> S<#> T<#>}

HAS_LOCKSCREEN

^{Simple lockscreen}

ACTIVATE_MESH_ITEM

^{Active Mesh Leveling menu option}

Configuration_adv.h

POWER_LOSS_RECOVERY

^{Continue Print after Power-Loss}

M114_DETAIL

^{Use 'M114' for details to check planner calculations}

CANCEL_OBJECTS

^{Use 'M486' to allow Marlin to skip objects}

AUTO_REPORT_POSITION

^{M154 S<seconds>}

EXTENDED_CAPABILITIES_REPORT

M115_GEOMETRY_REPORT

^{'M115' outputs Firmware Capabilities (enabled features)}

REALTIME_REPORTING_COMMANDS

^{Report position and state of the machine}

📚Versions

These are the configurations offered:

Bed Leveling Options

[ _Default-NP ]: Use if you have a near stock machine

^{Default No Probe}

[ _MM ]: Create a bed mesh without an auto bed probe

^{Manual Mesh Bed Leveling}

[ _BLT ]: Use if you have a CR/3D/BL-Touch level sensor installed.

^{Bilinear Auto Bed Leveling}

[ _UBL ]: Similar to both MM and BLT - with more options. Recommended over BLT

^{Unified Bed Leveling}

Special Versions

^{(List of file prefixes and suffixes)}

[ -ProUI-EX ]
| ProUI Extra Features |
Toolbar, change bed physical dimensions, and other special features and options
[ _E3-Free-runs ]
| Creality E3 Free-runs | (Creality board - TMC2209 drivers)
[ -S1<F1/F4> ]
| Creality Ender-3 S1 | (Check to see whether you have F1 or F4)
-S1-F1: STM32F103RC chip and CREALITY_V24S1_301 board

-S1-F4: STM32F401RC chip and CREALITY_V24S1_301F4 board

LCD Displays

[ DWIN ]
| Stock DWIN LCD | (No actual prefix)
[ TJC- ]
| Creality TJC LCD | (As aftermarket or sometimes used in stock Creality machines)
[ C2- ]
| Monochrome 128x64 LCD | (Used in Aquila C2 and original Ender-3/CR-10)

^{This has NO ProUI capabilities<...}

Contributors

gcardoso22, Nazar78, and wlkmanist

Assets 242

20 Nov 07:18

classicrocker883

2.1.3f-11-HC32-1

6d4c0e4

HC32 for November Rev.1

NOVEMBER 2024 Rev.1

Version: 2.1.3f-11-HC32-1

Continually updating with Marlin bugfix-2.1.x

_{⬂ List of recent updates ⬃}

^{What's new in this release}

⍟ Firmware Selector ⍟

Tip

You can use the Firmware Selector to help choose which file to download.

How to install the firmware

To update the firmware, choose the file ending in .bin and place it in your SD card:

^{(You may need to rename the file if reinstalling or if it doesn't flash the first time)}

For an Aquila board, put it inside a folder named "firmware"
For a Creality board, put it in the root folder of the drive
^{Or unless otherwise specified}

If you have not yet updated your LCD (since: November Rev.1),

please flash the new DWIN_SET now!

This is a universal firmware that has been optimized and enhanced for both the Voxelab Aquila and Creality Ender-3 V2/S1.
This is based on MriscoC's Professional Firmware for the Creality Ender-3 V2/S1. This particular build release is for the LCD color displays of Voxelab Aquila or similar variant. However, firmware for Aquila C2 monochrome LCD (128x64) are available. If you are using a Creality brand screen you can try the -TJC version. If you are not using HC32 chip, use the Aquila build here.

Recent Updates

EDITABLE_HOMING_FEEDRATE is now available in most, if not all, builds
Voxelab Aquila S3/X3 and use _IND - Induction Probe
Aquila C2 w/ monochrome 12864 LCD is supported having standard UI
BTT SKR Mini E3 V3 / V2 / V3.0.1 finally supported for ProUI - (4.3" Stock Aquila/Ender-3V2 Color LCD)

^{If you have a TFT or other display, you can request firmware *.bin files to be made, or compile your own}

BIQU MicroProbe V2.0 is now supported with _BMP prefix
Creality E3 Free-runs + Ender-3 S1 | F1/F4 board support (See Ender-3V2 build)

Important

🚩To use this version, you must✶ update the DWIN_SET to the LCD screen. New ICON's have been added, and others were remastered.

Choose a DWIN_SET from the "display assets" folder
Copy it to the root of an SD card
Remove the name in ( ) from the folder
^{e.g. "DWIN_SET (Original)" => "DWIN_SET"}
Open the back of the LCD, insert the card📲
Turn on power, wait until the screen goes Blue🔵 to Red🔴
Turn off, remove card⤵. Good to go!✅

✶ Technically you don't have to reflash the new DWIN_SET, but some ICON's will be missing if you do not.

Warning

🚧Please be aware of the following:

⚠️Previous Issue of it restarting when saving/store settings has been fixed. HOWEVER, now there is a current Issue to be addressed:
Everything so far seems to work correctly as it should, except for when an SD card is inserted. For some reason, if you may receive an "SD Card Init Fail" when first starting, just reinsert the card (it may take few times) or reboot. So printing may not always be possible using a card unless you use USB serial interface to upload the file (through a slicer or something like Pronterface).
More testing is needed, but it is fine for now.

⚠️Previous Gcode Preview Thumbnails Issue has been FIXED! Thank you @Nazar78 for your help.

While using _BLT or _MM versions, if you encounter the bed Mesh not saving...
This workaround resolves the issue without having to redo the mesh again.

Build Mesh (first time)
Save Mesh
After any time you Power Off and Power On -->
3a. Go to Control/Advanced Settings/Load Settings
-OR-
3b. Load this into your Start Gcode

G28 ; Home
M501 ; Load settings
M420 S1 ; Pull your mesh bed level
;(Remaining Gcode / Start Print)>>>

If you experience this issue as it starts printing --> Mesh leveling data is drawing over the printing screen
Go to Slicer Gcode Scripts

Note

⍰ The follow may apply to you if the mainboard chip supports 256KB max

Note ➀: Due to lack of flash memory space in the Aquila's GD32/N32|F103RCT6, some features had to be disabled in the ProUI of UBL and BLT versions, including, but not limited to:

Configuration.h

HOST_KEEPALIVE_FEATURE

^{Sends a busy status message to the host}

PREHEAT_2_LABEL

^'ABS'

PREHEAT_3_LABEL

^'Warmup'

G26_MESH_VALIDATION

^G26

NOZZLE_CLEAN_FEATURE

^{G12 P<#> S<#> T<#>}

HAS_LOCKSCREEN

^{Simple lockscreen}

ACTIVATE_MESH_ITEM

^{Active Mesh Leveling menu option}

Configuration_adv.h

POWER_LOSS_RECOVERY

^{Continue Print after Power-Loss}

M114_DETAIL

^{Use 'M114' for details to check planner calculations}

CANCEL_OBJECTS

^{Use 'M486' to allow Marlin to skip objects}

AUTO_REPORT_POSITION

^{M154 S<seconds>}

EXTENDED_CAPABILITIES_REPORT

M115_GEOMETRY_REPORT

^{'M115' outputs Firmware Capabilities (enabled features)}

REALTIME_REPORTING_COMMANDS

^{Report position and state of the machine}

📚Versions

These are the configurations offered:

Bed Leveling Options

[ _Default-NP ]: Use if you have a near stock machine

^{Default No Probe}

[ _MM ]: Create a bed mesh without an auto bed probe

^{Manual Mesh Bed Leveling}

[ _BLT ]: Use if you have a CR/3D/BL-Touch level sensor installed.

^{Bilinear Auto Bed Leveling}

[ _UBL ]: Similar to both MM and BLT - with more options. Recommended over BLT

Contributors

gcardoso22, Nazar78, and wlkmanist

Assets 32

20 Nov 07:25

classicrocker883

2.1.3f-11-1

84ef752

Aquila Build for November Rev.1 Latest

Latest

NOVEMBER 2024 Rev.1

Version: 2.1.3f-11-1

Continually updating with Marlin bugfix-2.1.x

_{⬂ List of recent updates ⬃}

^{What's new in this release}

⍟ Firmware Selector ⍟

Tip

You can use the Firmware Selector to help choose which file to download.

How to install the firmware

To update the firmware, choose the file ending in .bin and place it in your SD card:

^{(You may need to rename the file if reinstalling or if it doesn't flash the first time)}

For an Aquila board, put it inside a folder named "firmware"
For a Creality board, put it in the root folder of the drive
^{Or unless otherwise specified}

If you have not yet updated your LCD (since: November Rev.1),

please flash the new DWIN_SET now!

This is a universal firmware that has been optimized and enhanced for both the Voxelab Aquila and Creality Ender-3 V2/S1.
This is based on MriscoC's Professional Firmware for the Creality Ender-3 V2/S1. This particular build release is for the LCD color displays of Voxelab Aquila or similar variant. However, firmware for Aquila C2 monochrome LCD (128x64) are available. If you are using a Creality brand screen you can try the -TJC version, or the Ender-3V2 build here.

If you are using an Aquila S3, use firmware having _IND (Inductive Probe). You may need to adjust your Probe Offsets, specifically the Y Offset, set this to -20 or -25 as per this post here. From the Main Menu, go to Level > Probe Settings > Probe Y Offset.

Recent Updates

Power-Loss Recovery (-PLR) and EDITABLE_HOMING_FEEDRATE is now available in most, if not all, builds

^{Firmware with this prefix is not showing, but this feature is available}

HC32 Build linked here
Voxelab Aquila S3/X3 and use _IND - Induction Probe
Aquila C2 w/ monochrome 12864 LCD is supported having standard UI
BTT SKR Mini E3 V3 / V2 / V3.0.1 finally supported for ProUI - (4.3" Stock Aquila/Ender-3V2 Color LCD)

^{If you have a TFT or other display, you can request firmware *.bin files to be made, or compile your own}

BIQU MicroProbe V2.0 is now supported with _BMP prefix
Creality E3 Free-runs + Ender-3 S1 | F1/F4 board support (See Ender-3V2 build)

Important

🚩To use this version, you must✶ update the DWIN_SET to the LCD screen. New ICON's have been added, and others were remastered.

Choose a DWIN_SET from the "display assets" folder
Copy it to the root of an SD card
Remove the name in ( ) from the folder
^{e.g. "DWIN_SET (Original)" => "DWIN_SET"}
Open the back of the LCD, insert the card📲
Turn on power, wait until the screen goes Blue🔵 to Red🔴
Turn off, remove card⤵. Good to go!✅

✶ Technically you don't have to reflash the new DWIN_SET, but some ICON's will be missing if you do not.

Warning

🚧Please be aware of the following:

⚠️Previous Gcode Preview Thumbnails Issue has been FIXED! Thank you @Nazar78 for your help.

While using _BLT or _MM versions, if you encounter the bed Mesh not saving...
This workaround resolves the issue without having to redo the mesh again.

Build Mesh (first time)
Save Mesh
After any time you Power Off and Power On -->
3a. Go to Control/Advanced Settings/Load Settings
-OR-
3b. Load this into your Start Gcode

G28 ; Home
M501 ; Load settings
M420 S1 ; Pull your mesh bed level
;(Remaining Gcode / Start Print)>>>

If you experience this issue as it starts printing --> Mesh leveling data is drawing over the printing screen
The correct way of set the start G-code script is detailed in: Slicer Gcode Scripts
Otherwise I would advice just not using G29 to build a mesh in the Gcode, but instead manually make one before printing, or just make one mesh for all prints.

Note

⍰ The follow may apply to you if the mainboard chip supports 256KB max

Note ➀: Due to lack of flash memory space in the Aquila's GD32/N32|F103RCT6, some features had to be disabled in the ProUI of UBL and BLT versions, including, but not limited to:

Configuration.h

HOST_KEEPALIVE_FEATURE

^{Sends a busy status message to the host}

PREHEAT_2_LABEL

^'ABS'

PREHEAT_3_LABEL

^'Warmup'

G26_MESH_VALIDATION

^G26

NOZZLE_CLEAN_FEATURE

^{G12 P<#> S<#> T<#>}

HAS_LOCKSCREEN

^{Simple lockscreen}

ACTIVATE_MESH_ITEM

^{Active Mesh Leveling menu option}

Configuration_adv.h

POWER_LOSS_RECOVERY

^{Continue Print after Power-Loss}

M114_DETAIL

^{Use 'M114' for details to check planner calculations}

CANCEL_OBJECTS

^{Use 'M486' to allow Marlin to skip objects}

AUTO_REPORT_POSITION

^{M154 S<seconds>}

EXTENDED_CAPABILITIES_REPORT

M115_GEOMETRY_REPORT

^{'M115' outputs Firmware Capabilities (enabled features)}

REALTIME_REPORTING_COMMANDS

^{Report position and state of the machine}

📚Versions

These are the configurations offered:

Bed Leveling Options

[ _Default-NP ]: Use if you have a near stock machine

^{Default No Probe}

[ _MM ]: Create a bed mesh without an auto bed probe

^{Manual Mesh Bed Leveling}

[ _BLT ]: Use if you have a CR/3D/BL-Touch level sensor installed.

^...

Contributors

gcardoso22, Nazar78, and wlkmanist

Assets 392

Aquila_422_BLT-ProUI-EX-11-20.bin

207 KB 2024-11-20T07:33:34Z
Aquila_422_BLT-ProUI-EX-IS-11-20.bin

214 KB 2024-11-20T07:34:26Z
Aquila_422_BLT-ProUI-EX-IS-MPC-11-20.bin

219 KB 2024-11-20T07:34:21Z
Aquila_422_BLT-ProUI-EX-MPC-11-20.bin

213 KB 2024-11-20T07:33:37Z
Aquila_422_BMP_BLT-ProUI-EX-11-20.bin

203 KB 2024-11-20T07:33:02Z
Aquila_422_BMP_BLT-ProUI-EX-IS-11-20.bin

210 KB 2024-11-20T07:34:18Z
Aquila_422_BMP_BLT-ProUI-EX-IS-MPC-11-20.bin

215 KB 2024-11-20T07:34:33Z
Aquila_422_BMP_BLT-ProUI-EX-MPC-11-20.bin

209 KB 2024-11-20T07:33:29Z
Aquila_422_BMP_UBL-ProUI-EX-11-20.bin

217 KB 2024-11-20T07:41:24Z
Aquila_422_BMP_UBL-ProUI-EX-IS-11-20.bin

223 KB 2024-11-20T07:42:52Z
Source code (zip)

2024-11-20T06:43:58Z
Source code (tar.gz)

2024-11-20T06:43:58Z

03 Nov 14:42

classicrocker883

2.1.3f-11-HC32

7a96848

HC32 for November

NOVEMBER 2024

Version: 2.1.3f-11-HC32

Continually updating with Marlin bugfix-2.1.x

_{⬂ List of recent updates ⬃}

^{What's new in this release}

⍟ Firmware Selector ⍟

Tip

You can use the Firmware Selector to help choose which file to download.

How to install the firmware

To update the firmware, choose the file ending in .bin and place it in your SD card:

^{(You may need to rename the file if reinstalling or if it doesn't flash the first time)}

For an Aquila board, put it inside a folder named "firmware"
For a Creality board, put it in the root folder of the drive
^{Or unless otherwise specified}

If you have not yet updated your LCD (since: November Rev.1),

please flash the new DWIN_SET now!

This is a universal firmware that has been optimized and enhanced for both the Voxelab Aquila and Creality Ender-3 V2/S1.
This is based on MriscoC's Professional Firmware for the Creality Ender-3 V2/S1. This particular build release is for the LCD color displays of Voxelab Aquila or similar variant. However, firmware for Aquila C2 monochrome LCD (128x64) are available. If you are using a Creality brand screen you can try the -TJC version. If you are not using HC32 chip, use the Aquila build here.

Recent Updates

EDITABLE_HOMING_FEEDRATE is now available in most, if not all, builds
Voxelab Aquila S3/X3 and use _IND - Induction Probe
Aquila C2 w/ monochrome 12864 LCD is supported having standard UI
BTT SKR Mini E3 V3 / V2 / V3.0.1 finally supported for ProUI - (4.3" Stock Aquila/Ender-3V2 Color LCD)

^{If you have a TFT or other display, you can request firmware *.bin files to be made, or compile your own}

BIQU MicroProbe V2.0 is now supported with _BMP prefix
Creality E3 Free-runs + Ender-3 S1 | F1/F4 board support (See Ender-3V2 build)

Important

🚩To use this version, you must✶ update the DWIN_SET to the LCD screen. New ICON's have been added, and others were remastered.

Choose a DWIN_SET from the "display assets" folder
Copy it to the root of an SD card
Remove the name in ( ) from the folder
^{e.g. "DWIN_SET (Original)" => "DWIN_SET"}
Open the back of the LCD, insert the card📲
Turn on power, wait until the screen goes Blue🔵 to Red🔴
Turn off, remove card⤵. Good to go!✅

✶ Technically you don't have to reflash the new DWIN_SET, but some ICON's will be missing if you do not.

Warning

🚧Please be aware of the following:

⚠️Previous Gcode Preview Thumbnails Issue has been FIXED! Thank you @Nazar78 for your help.

While using _BLT or _MM versions, if you encounter the bed Mesh not saving...
This workaround resolves the issue without having to redo the mesh again.

Build Mesh (first time)
Save Mesh
After any time you Power Off and Power On -->
3a. Go to Control/Advanced Settings/Load Settings
-OR-
3b. Load this into your Start Gcode

G28 ; Home
M501 ; Load settings
M420 S1 ; Pull your mesh bed level
;(Remaining Gcode / Start Print)>>>

If you experience this issue as it starts printing --> Mesh leveling data is drawing over the printing screen
Go to Slicer Gcode Scripts

Note

⍰ The follow may apply to you if the mainboard chip supports 256KB max

Note ➀: Due to lack of flash memory space in the Aquila's GD32/N32|F103RCT6, some features had to be disabled in the ProUI of UBL and BLT versions, including, but not limited to:

Configuration.h

HOST_KEEPALIVE_FEATURE

^{Sends a busy status message to the host}

PREHEAT_2_LABEL

^'ABS'

PREHEAT_3_LABEL

^'Warmup'

G26_MESH_VALIDATION

^G26

NOZZLE_CLEAN_FEATURE

^{G12 P<#> S<#> T<#>}

HAS_LOCKSCREEN

^{Simple lockscreen}

ACTIVATE_MESH_ITEM

^{Active Mesh Leveling menu option}

Configuration_adv.h

POWER_LOSS_RECOVERY

^{Continue Print after Power-Loss}

M114_DETAIL

^{Use 'M114' for details to check planner calculations}

CANCEL_OBJECTS

^{Use 'M486' to allow Marlin to skip objects}

AUTO_REPORT_POSITION

^{M154 S<seconds>}

EXTENDED_CAPABILITIES_REPORT

M115_GEOMETRY_REPORT

^{'M115' outputs Firmware Capabilities (enabled features)}

REALTIME_REPORTING_COMMANDS

^{Report position and state of the machine}

📚Versions

These are the configurations offered:

Bed Leveling Options

[ _Default-NP ]: Use if you have a near stock machine

^{Default No Probe}

[ _MM ]: Create a bed mesh without an auto bed probe

^{Manual Mesh Bed Leveling}

[ _BLT ]: Use if you have a CR/3D/BL-Touch level sensor installed.

^{Bilinear Auto Bed Leveling}

[ _UBL ]: Similar to both MM and BLT - with more options. Recommended over BLT

^U...

Contributors

gcardoso22, Nazar78, and wlkmanist

Assets 32

03 Nov 12:35

classicrocker883

2.1.3f-11-ender3

0c1ecac

Ender-3V2 Build for November

NOVEMBER 2024

Version: 2.1.3f-11-ender3

Continually updating with Marlin bugfix-2.1.x

_{⬂ List of recent updates ⬃}

^{What's new in this release}

⍟ Firmware Selector ⍟

Tip

You can use the Firmware Selector to help choose which file to download.

How to install the firmware

To update the firmware, choose the file ending in .bin and place it in your SD card:

^{(You may need to rename the file if reinstalling or if it doesn't flash the first time)}

For a Creality board, put it in the root folder of the drive
^{Or unless otherwise specified}

If you have not yet updated your LCD (since: November Rev.1),

please flash the new DWIN_SET now!

Recent Updates

EDITABLE_HOMING_FEEDRATE is now available in most, if not all, builds
BTT SKR Mini E3 V3 / V2 / V3.0.1 finally supported for ProUI - (4.3" Stock Aquila/Ender-3V2 Color LCD)

^{If you have a TFT or other display, you can request firmware *.bin files to be made, or compile your own}

BIQU MicroProbe V2.0 is now supported with _BMP prefix
Creality E3 Free-runs + Ender-3 S1 | F1/F4 board support

Important

🚩To use this version, you must✶ update the DWIN_SET to the LCD screen. New ICON's have been added, and others were remastered.

Choose a DWIN_SET from the "display assets" folder
Copy it to the root of an SD card
Remove the name in ( ) from the folder
^{e.g. "DWIN_SET (Original)" => "DWIN_SET"}
Open the back of the LCD, insert the card📲
Turn on power, wait until the screen goes Blue🔵 to Red🔴
Turn off, remove card⤵. Good to go!✅

✶ Technically you don't have to reflash the new DWIN_SET, but some ICON's will be missing if you do not.

Warning

🚧Please be aware of the following:

⚠️Previous Gcode Preview Thumbnails Issue has been FIXED! Thank you @Nazar78 for your help.

While using _BLT or _MM versions, if you encounter the bed Mesh not saving...
This workaround resolves the issue without having to redo the mesh again.

Build Mesh (first time)
Save Mesh
After any time you Power Off and Power On -->
3a. Go to Control/Advanced Settings/Load Settings
-OR-
3b. Load this into your Start Gcode

G28 ; Home
M501 ; Load settings
M420 S1 ; Pull your mesh bed level
;(Remaining Gcode / Start Print)>>>

If you experience this issue as it starts printing --> Mesh leveling data is drawing over the printing screen
Go to Slicer Gcode Scripts

Note

⍰ The follow may apply to you if the mainboard chip supports 256KB max

Note ➀: Due to lack of flash memory space in the Aquila's GD32/N32|F103RCT6, some features had to be disabled in the ProUI of UBL and BLT versions, including, but not limited to:

Configuration.h

HOST_KEEPALIVE_FEATURE

^{Sends a busy status message to the host}

PREHEAT_2_LABEL

^'ABS'

PREHEAT_3_LABEL

^'Warmup'

G26_MESH_VALIDATION

^G26

NOZZLE_CLEAN_FEATURE

^{G12 P<#> S<#> T<#>}

HAS_LOCKSCREEN

^{Simple lockscreen}

ACTIVATE_MESH_ITEM

^{Active Mesh Leveling menu option}

Configuration_adv.h

POWER_LOSS_RECOVERY

^{Continue Print after Power-Loss}

M114_DETAIL

^{Use 'M114' for details to check planner calculations}

CANCEL_OBJECTS

^{Use 'M486' to allow Marlin to skip objects}

AUTO_REPORT_POSITION

^{M154 S<seconds>}

EXTENDED_CAPABILITIES_REPORT

M115_GEOMETRY_REPORT

^{'M115' outputs Firmware Capabilities (enabled features)}

REALTIME_REPORTING_COMMANDS

^{Report position and state of the machine}

📚Versions

These are the configurations offered:

Bed Leveling Options

[ _Default-NP ]: Use if you have a near stock machine

^{Default No Probe}

[ _MM ]: Create a bed mesh without an auto bed probe

^{Manual Mesh Bed Leveling}

[ _BLT ]: Use if you have a CR/3D/BL-Touch level sensor installed.

^{Bilinear Auto Bed Leveling}

[ _UBL ]: Similar to both MM and BLT - with more options. Recommended over BLT

^{Unified Bed Leveling}

Special Versions

^{(List of file prefixes and suffixes)}

[ -ProUI-EX ]
| ProUI Extra Features |
Toolbar, change bed physical dimensions, and other special features and options
[ _E3-Free-runs ]
| Creality E3 Free-runs | (Creality board - TMC2209 drivers)
[ -S1<F1/F4> ]
| Creality Ender-3 S1 | (Check to see whether you have F1 or F4)
-S1-F1: STM32F103RC chip and CREALITY_V24S1_301 board

-S1-F4: STM32F401RC chip and CREALITY_V24S1_301F4 board

LCD Displays

[ DWIN ]
| Stock DWIN LCD | (No actual prefix)
[ TJC- ]
| Creality TJC LCD | (As aftermarket or sometimes used in stock Creality machines)
[ C2- ]
| Monochrome 128x64 LCD | (Used in Aquila C2 and original Ender-3/CR-10)

^{This has NO ProUI capabilities}

...

Contributors

gcardoso22, Nazar78, and wlkmanist

Assets 242

03 Nov 12:41

classicrocker883

2.1.3f-11

0c1ecac

Aquila Build for November

NOVEMBER 2024

Version: 2.1.3f-11

Continually updating with Marlin bugfix-2.1.x

_{⬂ List of recent updates ⬃}

^{What's new in this release}

⍟ Firmware Selector ⍟

Tip

You can use the Firmware Selector to help choose which file to download.

How to install the firmware

To update the firmware, choose the file ending in .bin and place it in your SD card:

^{(You may need to rename the file if reinstalling or if it doesn't flash the first time)}

For an Aquila board, put it inside a folder named "firmware"
For a Creality board, put it in the root folder of the drive
^{Or unless otherwise specified}

If you have not yet updated your LCD (since: November Rev.1),

please flash the new DWIN_SET now!

This is a universal firmware that has been optimized and enhanced for both the Voxelab Aquila and Creality Ender-3 V2/S1.
This is based on MriscoC's Professional Firmware for the Creality Ender-3 V2/S1. This particular build release is for the LCD color displays of Voxelab Aquila or similar variant. However, firmware for Aquila C2 monochrome LCD (128x64) are available. If you are using a Creality brand screen you can try the -TJC version, or the Ender-3V2 build here.

Recent Updates

Power-Loss Recovery (-PLR) and EDITABLE_HOMING_FEEDRATE is now available in most, if not all, builds

^{Firmware with this prefix is not showing, but this feature is available}

HC32 Build linked here
Voxelab Aquila S3/X3 and use _IND - Induction Probe
Aquila C2 w/ monochrome 12864 LCD is supported having standard UI
BTT SKR Mini E3 V3 / V2 / V3.0.1 finally supported for ProUI - (4.3" Stock Aquila/Ender-3V2 Color LCD)

^{If you have a TFT or other display, you can request firmware *.bin files to be made, or compile your own}

BIQU MicroProbe V2.0 is now supported with _BMP prefix
Creality E3 Free-runs + Ender-3 S1 | F1/F4 board support (See Ender-3V2 build)

Important

🚩To use this version, you must✶ update the DWIN_SET to the LCD screen. New ICON's have been added, and others were remastered.

Choose a DWIN_SET from the "display assets" folder
Copy it to the root of an SD card
Remove the name in ( ) from the folder
^{e.g. "DWIN_SET (Original)" => "DWIN_SET"}
Open the back of the LCD, insert the card📲
Turn on power, wait until the screen goes Blue🔵 to Red🔴
Turn off, remove card⤵. Good to go!✅

✶ Technically you don't have to reflash the new DWIN_SET, but some ICON's will be missing if you do not.

Warning

🚧Please be aware of the following:

⚠️Previous Gcode Preview Thumbnails Issue has been FIXED! Thank you @Nazar78 for your help.

While using _BLT or _MM versions, if you encounter the bed Mesh not saving...
This workaround resolves the issue without having to redo the mesh again.

Build Mesh (first time)
Save Mesh
After any time you Power Off and Power On -->
3a. Go to Control/Advanced Settings/Load Settings
-OR-
3b. Load this into your Start Gcode

G28 ; Home
M501 ; Load settings
M420 S1 ; Pull your mesh bed level
;(Remaining Gcode / Start Print)>>>

Note

⍰ The follow may apply to you if the mainboard chip supports 256KB max

Note ➀: Due to lack of flash memory space in the Aquila's GD32/N32|F103RCT6, some features had to be disabled in the ProUI of UBL and BLT versions, including, but not limited to:

Configuration.h

HOST_KEEPALIVE_FEATURE

^{Sends a busy status message to the host}

PREHEAT_2_LABEL

^'ABS'

PREHEAT_3_LABEL

^'Warmup'

G26_MESH_VALIDATION

^G26

NOZZLE_CLEAN_FEATURE

^{G12 P<#> S<#> T<#>}

HAS_LOCKSCREEN

^{Simple lockscreen}

ACTIVATE_MESH_ITEM

^{Active Mesh Leveling menu option}

Configuration_adv.h

POWER_LOSS_RECOVERY

^{Continue Print after Power-Loss}

M114_DETAIL

^{Use 'M114' for details to check planner calculations}

CANCEL_OBJECTS

^{Use 'M486' to allow Marlin to skip objects}

AUTO_REPORT_POSITION

^{M154 S<seconds>}

EXTENDED_CAPABILITIES_REPORT

M115_GEOMETRY_REPORT

^{'M115' outputs Firmware Capabilities (enabled features)}

REALTIME_REPORTING_COMMANDS

^{Report position and state of the machine}

📚Versions

These are the configurations offered:

Bed Leveling Options

[ _Default-NP ]: Use if you have a near stock machine

^{Default No Probe}

[ _MM ]: Create a bed mesh without an auto bed probe

^{Manual Mesh Bed Leveling}

[ _BLT ]: Use if you have a CR/3D/BL-Touch level sensor installed.

Contributors

gcardoso22, Nazar78, and wlkmanist

Assets 392

Releases: classicrocker883/MRiscoCProUI

Aquila Test Github Actions - Python 3.10

Aquila Test HKF

Aquila Test Github Actions - Revert versions @main

Ender-3V2 Build for November Rev.1a

NOVEMBER 2024 Rev.1a

❗❗NOTHING NEW IN THIS RELEASE❗❗ Just added support for Creality Spider Speedy Ceramic Hotend Look for _SPDY5 For Example: Ender_SPDY5_427_UBL-ProUI-EX-11-23.bin So this release is same as previous Rev.1 Disregard firmware unless you have this type of hotend

Version: 2.1.3f-11-ender3-1a

Continually updating with Marlin bugfix-2.1.x

⬂ List of recent updates ⬃

⍟ Firmware Selector ⍟

**Recent Updates**

🚧Please be aware of the following:

📚Versions

Bed Leveling Options

Special Versions

Contributors

Ender-3V2 Build for November Rev.1

NOVEMBER 2024 Rev.1

Version: 2.1.3f-11-ender3-1

Continually updating with Marlin bugfix-2.1.x

⬂ List of recent updates ⬃

⍟ Firmware Selector ⍟

**Recent Updates**

🚧Please be aware of the following:

📚Versions

Bed Leveling Options

Special Versions

Contributors

HC32 for November Rev.1

NOVEMBER 2024 Rev.1

Version: 2.1.3f-11-HC32-1

Continually updating with Marlin bugfix-2.1.x

⬂ List of recent updates ⬃

⍟ Firmware Selector ⍟

**Recent Updates**

🚧Please be aware of the following:

📚Versions

Bed Leveling Options

Contributors

Aquila Build for November Rev.1

NOVEMBER 2024 Rev.1

Version: 2.1.3f-11-1

Continually updating with Marlin bugfix-2.1.x

⬂ List of recent updates ⬃

⍟ Firmware Selector ⍟

**Recent Updates**

🚧Please be aware of the following:

📚Versions

Bed Leveling Options

Contributors

HC32 for November

NOVEMBER 2024

Version: 2.1.3f-11-HC32

Continually updating with Marlin bugfix-2.1.x

⬂ List of recent updates ⬃

⍟ Firmware Selector ⍟

**Recent Updates**

🚧Please be aware of the following:

📚Versions

Bed Leveling Options

Contributors

Ender-3V2 Build for November

NOVEMBER 2024

Version: 2.1.3f-11-ender3

Continually updating with Marlin bugfix-2.1.x

⬂ List of recent updates ⬃

⍟ Firmware Selector ⍟

**Recent Updates**

🚧Please be aware of the following:

📚Versions

Bed Leveling Options

Special Versions

Contributors

Aquila Build for November

NOVEMBER 2024

Version: 2.1.3f-11

Continually updating with Marlin bugfix-2.1.x

⬂ List of recent updates ⬃

⍟ Firmware Selector ⍟

❗❗NOTHING NEW IN THIS RELEASE❗❗
Just added support for Creality Spider Speedy Ceramic Hotend
Look for _SPDY5
For Example:
Ender_SPDY5_427_UBL-ProUI-EX-11-23.bin

So this release is same as previous Rev.1

Disregard firmware unless you have this type of hotend

_{⬂ List of recent updates ⬃}

Recent Updates

_{⬂ List of recent updates ⬃}

Recent Updates

_{⬂ List of recent updates ⬃}

Recent Updates

_{⬂ List of recent updates ⬃}

Recent Updates

_{⬂ List of recent updates ⬃}

Recent Updates

_{⬂ List of recent updates ⬃}

Recent Updates

_{⬂ List of recent updates ⬃}

Recent Updates