2.0.3

By downloading this software, you agree to the Rad Pro terms and conditions.

Note: this release requires an installation.

Release notes:

• Extended conversion factor range to 25-12800 cpm/µSv/h.
• When using sensitive detectors with a conversion factor of 600 cpm/µSv/h or higher, Rad Pro caps the pulse indication at 600 cpm/µSv/h to provide approximately one pulse per second at background levels of radiation. This does not impact the actual measurement.
• Minor UI and performance refinements.
• Added the Rad Pro simulator.

2.0.2 (flashtool v2)

By downloading this software, you agree to the Rad Pro terms and conditions.

Instructions:

• Use the update version if you have Rad Pro 2.0.1 installed.
• Use the install version if you have Rad Pro 2.0.0 or earlier intalled.

Release notes:

• Improved the instantaneous rate averaging algorithm.
• Simplified the instantaneous rate averaging response curves, resulting in improved precision when using J613/J614 tubes.
• Disabled instantaneous rate alarms in situations where the confidence interval is high, such as immediately after device startup.
• Minor UI improvements.
• Fixes an error in the flashtool (with FNIRSI GC-01 devices).

2.0.1

By downloading this software, you agree to the Rad Pro terms and conditions.

Notes:

• Added data log reset.
• Changed the default conversion factor for J613/J614 tubes to 60.0 cpm/µSv/h.
• Resolved issues with custom HV profiles.
• Resolved issues with the "SET tubeHVFrequency" and "SET tubeHVDutyCycle" data connection requests.
• Resolved issues with new history data log download.
• Minor refinements.

2.0

By downloading this software, you agree to the Rad Pro terms and conditions.

Notes:

• First 2.0 release.
• Updated the UI design system to OpenBridge 5.0, improving legibility under sunlight.
• Changed the default conversion factor for J613/J614 tubes to 30.0 cpm/µSv/h.
• Removed the FNIRSI GC-01 display panel settings.
• Increased the granularity and range of the "SET tubeHVFrequency" and "SET tubeHVDutyCycle" data connection requests to 100 Hz-100 kHz and 0 %-100 %, respectively (not stored on power-off).

2.0rc5 The final countdown

By downloading this software, you agree to the Rad Pro terms and conditions.

On FNIRSI GC-01 devices, make sure you select the correct display panel in display settings!

Notes:

• Added Bosean FS-5000 support.
• Added display panel menu for selecting the display panel (on supported devices).
• Added secondary dose view in average measurement mode.
• Extended conversion factor range to 25-1600 cpm/µSv/h.
• Added 1 second datalog interval options and removed 30 seconds and 30 minutes datalog interval options.
• Added "SET tubeHVFrequency" and "SET tubeHVDutyCycle" data connection commands.
• Added 12-hour time format.
• Devices with data mode allow using the device while data mode is active; data mode state is also preserved after powering off.
• Improved battery level indicator of the Bosean FS-600/FS-1000.
• Improved battery level readout of the FS2011(STM32F051), Bosean FS-600/FS-1000.
• Improved keyboard control scheme of the Bosean FS-1000.
• Changed USB data connection end of line to "\r\n".
• Minor refinements.

2.0rc4 The "little" update

By downloading this software, you agree to the Rad Pro terms and conditions.

Notes:

• Added instantaneous rate averaging options: adaptive fast, adaptive precision, 60 seconds, 30 seconds and 10 seconds.
• Added secondary CPM and count displays in measurement views.
• Improved haptic pulse strengths.
• Improved FNIRSI GC-01 quiet pulse clicks.
• Improved selected menu item contrast.
• Improved datalogging time precision.
• Fixed History (24 h) bug.

2.0rc3 The "BIG" update

By downloading this software, you agree to the Rad Pro terms and conditions.

Notes:

• UI update with BIG numbers.
• Instantaneous rate bar with alert zones (1 µSv, 10 µSv).
• History alert zones (1 µSv, 10 µSv).
• Average timer expiration after reaching a configurable confidence interval.
• Background compensation.
• Display flashes on the FNIRSI GC-01 (after display sleep).
• Haptic pulses on the FNIRSI GC-01 (off, weak or strong).
• Pulses threshold (disables pulse indication if instantaneous rate is below a certain value).
• Fault alarm on HV/tube failure (lack of pulses) or tube saturation (tube shorted).
• Added 30 second and 10 second datalog interval options.
• Added 10 second display sleep option.
• Added radpro-flashtool.
• Removed hold option.

2.0rc2

By downloading this software, you agree to the Rad Pro terms and conditions.

Notes:

• Changed default display theme to Dusk.
• Fixed flash programming code.
• Fixed FNIRSI GC-01 battery indicator.
• Fixed conversion factor menu logic.

1.3.0

By downloading this software, you agree to the Rad Pro terms and conditions.

Note: Rad Pro 1.3.0 uses a new settings format, thus requiring an installation rather than an update.

Notes:

• Added data logging.
• Added custom conversion factors.
• Added support for the J305 Geiger tube.
• Minor bug fixes.

1.2.2

• Added support for devices with a GD32 microcontroller.
• Added data submission to the https://gmcmap.com/ radiation monitoring website.