Smart Irrigation

Versions since v0.0.30 introduced a number of bugs. As a result we have reverted back to v0.0.29 and implemented bug fixes only from there. Versions from v0.0.40 onwards should work correctly. Change percentage feature has been removed while we work on bringing it back later. You will see references to it in the code as it has been temporarily removed from the options screen and any calculations. We apologize for any inconvenience caused.

Smart Irrigation custom component for Home Assistant. Partly based on the excellent work at https://github.com/hhaim/hass/. This component calculates the time to run your irrigation system to compensate for moisture lost by evaporation / evapotranspiration. Using this component you water your garden, lawn or crops precisely enough to compensate what has evaporated. It takes into account precipitation (rain,snow) and adjusts accordingly, so if it rains or snows less or no irrigation is required. By adding multiple instances of this component multiple zones can be supported as each zone will have its own sprinkler and flow configuration.

Note - use this component at your own risk - we do not assume responsibility for any inconvience caused by using this component. Always use common sense before deciding to irrigate using the calculations this component provides. For example, irrigating during excessive rainfall might cause flooding. Again - we assume no responsibility for any inconvience caused.

The component keeps track of hourly precipitation and at 23:00 (11:00 PM) local time stores it in a daily value. It then calculates the exact runtime in seconds to compensate for the net evaporation. Note that this is the default behavior and this can be disabled if you want more control. Also, the time auto refresh happens (if not disabled) is configurable. This is all the component does, and this is on purpose to provide maximum flexibility. Users are expected to use the value of sensor.smart_irrigation.daily_adjusted_run_time to interact with their irrigation system and afterwards call the smart_irrigation.reset_bucket service. See the example automations below.

This component uses reference evapotranspiration values and calculates base schedule indexes and water budgets from that. This is an industry-standard approach. Information can be found at https://www.rainbird.com/professionals/irrigation-scheduling-use-et-save-water, amongst others. The component uses the PyETo module to calculate the evapotranspiration value (fao56). Also, please see the How this works Wiki page.

Operation modes

You can use this component in various modes:

1. Full Open Weather Map. In this mode all data comes from the Open Weather Map service. You will need to create and provide an API key. See Getting Open Weater Map API Key below for instructions.
2. Full Sensors. Using sensors. In this mode all data comes from sensors such as a weather station. When specificying a sensor for precipitation, note that it needs to be a cumulative daily sensor. Open Weather Map is not used and you do not need an API key.
3. Mixed. A combination of 1) and 2). In this mode part of the data is supplied by sensors and part by Open Weather Map. In this mode you will need to create and provide an API key. See Getting Open Weater Map API Key below for instructions. When specificying a sensor for precipitation, note that it needs to be a cumulative daily sensor.
4. Not calculating. This mode allows you to skip the calculations of evapotranspiration all together and instead rely on a sensor to provide this value. In this mode, you will need to specify a precipitation sensor as well. Both of these need to be a cumulative daily sensor.

When planning to set up mode 2) (Full Sensors), 3) (Mixed) or 4) (Not Calculating) see Measurements and Units for more information on the measurements and units expected by this component.

Getting the best results

In order to get the most accurate results using sensors is preferable either from your own weather station or from another, from example through Weatherflow Smart Weather. If you have a weather station that provides evapotranspiration (ET) values, use that (mode 4). If you do not have that, use sensors including solar radiation (mode 3). If you do not have access to a sensor that provides solar radiation, let this component estimate it but use sensors for the other inputs (modified mode 3). If you do have access to limited amount of sensors (say only temperature) use that and use Open Weather Map for the rest (mode 2). If you do not have access to any sensors at all use Open Weather Map (mode 1).

Since this component provides multiple configuration options it might get confusing about in which scenario what behavior can be expected and what input is required. In the table below we summarize the configuration modes, their accuracy, the required input and how daily adjusted run time is calculated. Keep in mind that daily adjusted run time is based on the netto precipitation (precipitation - evapotranspiration) and the bucket value for previous days.

Mode	Accuracy	Input	How adjusted run time is calculated
Mode 1 - Full Open Weather Map	Low	No sensor input required, just an API key for Open Weather Map	Average of precipitation and evapotranspiration.
Mode 2 - Full Sensor, but calculating evapotranspiration	High	Sensors are required for all inputs. All inputs are expected to be point-in-time, except precipitation. That sensor is normally provided by a weather station or weather service as a daily accumulative / 'total precipitation today' sensor and that is what is expected by the component	Most recent value for precipitation and average of evapotranspiration.
Mode 3 - Mixed	Medium	API key is required for any inputs that have not been provided sensors. All inputs are expected to be point-in-time, except precipitation. That sensor is normally provided by a weather station or weather service as a 'total precipitation today' sensor and that is what is expected by the component	If a sensor is provided for precipitation, most recent value for precipitation is used. Otherwise the average of both precipitation and evapotranspiration.
Mode 4 -Not calculating	Very high	In this mode, just two sensors are required: one for precipitation and one for evapotranspiration. Both are expected to be daily accumulative sensors ('total today'), as is normally the case when provided by a weather service or weather station.	Most recent value of both precipitation and evapotranspiration.

Configuration

In this section:

• One-time set up
• List of events, services entities and attributes created
• Example automation
• Optional settings

Step 1: configuration of component

Install the custom component (preferably using HACS) and then use the Configuration --> Integrations pane to search for 'Smart Irrigation'. You will need to specify the following:

• Names of sensors that supply required measurements (optional). Only required in mode 2) and 3). See Measurements and Units for more information on the measurements and units expected by this component.
• API Key for Open Weather Map (optional). Only required in mode 1) and 3). See Getting Open Weater Map API Key below for instructions.
• Reference Evapotranspiration for all months of the year. See Getting Monthly ET values below for instructions. Note that you can specify these in inches or mm, depending on your Home Assistant settings.
• Number of sprinklers in your irrigation system
• Flow per spinkler in gallons per minute or liters per minute. Refer to your sprinkler's manual for this information.
• Area that the sprinklers cover in square feet or m²

When entering any values in the configuration of this component, keep in mind that the component will expect inches, sq ft, gallons, gallons per minute, or mm, m², liters, liters per minute respectively depending on the settings in Home Assistant (imperial vs metric system). For sensor configuration take care to make sure the unit the component expects is the same as your sensor provides.

Step 2: checking services, events and entities

After successful configuration, you should end up with three entities and their attributes, listed below as well as three services.

Services

For each instance of the component the following services will be available:

Service	Description
smart_irrigation.[instance]_calculate_daily_adjusted_run_time	Triggers the calculation of daily adjusted run time. Use only if you disabled automatic refresh in the options.
smart_irrigation.[instance]_calculate_hourly_adjusted_run_time	Triggers the calculation of hourly adjusted run time. Use for debugging only.
smart_irrigation.[instance]_enable_force_mode	Enables force mode.
smart_irrigation.[instance]_disable_force_mode	Disables force mode.
smart_irrigation.]instance]_reset_bucket	Resets the bucket to 0. Needs to be called after done irrigating (see below).
smart_irrigation.[instance]_set_bucket	Sets the bucket to the provided value. Use for debugging only.

Events

The component uses a number of events internally that you do not need to pay attention to unless you need to debug things. The exception is the _start event.

Event	Description
[instance]_start	Fires depending on daily_adjusted_run_time value and sunrise. You can listen to this event to optimize the moment you irrigate so your irrigation starts just before sunrise and is completed at sunrise. See below for examples on how to use this.
[instance]_bucketUpd	Fired when the bucket is calculated. Happens at automatic refresh time or as a result of the reset_bucket, set_bucket or calculate_daily_adjusted_run_time service.
[instance]_forceModeTog	Fired when the force mode is disabled or enabled. Result of calling enable_force_mode or disable_force_mode
[instance]_hourlyUpd	Fired when the hourly adjusted run time is calculated. Happens approximately every hour and when calculate_hourly_adjusted_run_time service is called.

Entities

sensor.smart_irrigation_base_schedule_index

The number of seconds the irrigation system needs to run assuming maximum evapotranspiration and no rain / snow. This value and the attributes are static for your configuration. Attributes:

Attribute	Description
number of sprinklers	number of sprinklers in the system
flow	amount of water that flows through a single sprinkler in liters or gallon per minute
throughput	total amount of water that flows through the irrigation system in liters or gallon per minute.
reference evapotranspiration	the reference evapotranspiration values provided by the user - one for each month.
area	the total area the irrigation system reaches in m2 or sq ft.
precipitation rate	the output of the irrigation system across the whole area in mm or inch per hour
base schedule index minutes	the value of the entity in minutes instead of seconds
auto refresh	indicates if automatic refresh is enabled.
auto refresh time	time that automatic refresh will happen, if enabled.
force mode duration	duration of irrigation in force mode (seconds).

Sample screenshot:

sensor.smart_irrigation_hourly_adjusted_run_time

The adjusted run time in seconds to compensate for any net moisture lost. Updated approx. every 60 minutes. Attributes:

Attribute	Description
rain	the predicted (when using Open Weather Map) or cumulative daily (when using a sensor) rainfall in mm or inch
snow	the predicted (when using Open Weather Map, will be 0 when using a sensor) snowfall in mm or inch
precipitation	the total precipitation (which is the sum of rain and snow in mm or inch
evapotranspiration	the expected evapotranspiration
netto precipitation	the net evapotranspiration in mm or inch, negative values mean more moisture is lost than gets added bu rain/snow, while positive values mean more value is added by rain/snow than evaporates, equal to precipitation - evapotranspiration
water budget	percentage of expected evapotranspiration vs peak evapotranspiration
adjusted run time minutes	adjusted run time in minutes instead of seconds.

Sample screenshot:

sensor.smart_irrigation_daily_adjusted_run_time

The adjusted run time in seconds to compensate for any net moisture lost. Updated every day at 11:00 PM / 23:00 hours local time. Use this value for your automation (see step 3, below). Attributes:

Attribute	Description
water budget	percentage of net precipitation / base schedule index
bucket	running total of net precipitation. Negative values mean that irrigation is required. Positive values mean that more moisture was added than has evaporated yet, so irrigation is not required. Should be reset to 0 after each irrigation, using the smart_irrigation.reset_bucket service
lead_time	time in seconds to add to any irrigation. Very useful if your system needs to handle another task first, such as building up pressure.
maximum_duration	maximum duration in seconds for any irrigation, including any lead_time.
adjusted run time minutes	adjusted run time in minutes instead of seconds.

Sample screenshot:

You will use sensor.smart_irrigation_daily_adjusted_run_time to create an automation (see step 3, below).

The How this works Wiki page describes the entities, the attributes and the calculations.

Showing other attributes as entities (sensors)

See the Wiki for more information on how to expose other values this components calculates as sensors.

Step 3: creating automation

Since this component does not interface with your irrigation system directly, you will need to use the data it outputs to create an automation that will start and stop your irrigation system for you. This way you can use this custom component with any irrigation system you might have, regardless of how that interfaces with Home Assistant. In order for this to work correctly, you should base your automation on the value of sensor.smart_irrigation_daily_adjusted_run_time as long as you run your automation after it was updated (11:00 PM / 23:00 hours local time). If that value is above 0 it is time to irrigate. Note that the value is the run time in seconds. Also, after irrigation, you need to call the smart_irrigation.reset_bucket service to reset the net irrigation tracking to 0.

The last step in any automation is very important, since you will need to let the component know you have finished irrigating and the evaporation counter can be reset by calling the smart_irrigation.reset_bucket service

Example automation 1: one valve, potentially daily irrigation

Here is an example automation that runs when the smart_irrigation_start event is fired. It checks if sensor.smart_irrigation_daily_adjusted_run_time is above 0 and if it is it turns on switch.irrigation_tap1, waits the number of seconds as indicated by sensor.smart_irrigation_daily_adjusted_run_time and then turns off switch.irrigation_tap1. Finally, it resets the bucket by calling the smart_irrigation.reset_bucket service. If you have multiple instances you will need to adjust the event, entities and service names accordingly.

- alias: Smart Irrigation
  description: 'Start Smart Irrigation at 06:00 and run it only if the adjusted_run_time is >0 and run it for precisely that many seconds'
  trigger:
   - event_data: {}
     event_type: smart_irrigation_start
     platform: event
  condition:
  - above: '0'
    condition: numeric_state
    entity_id: sensor.smart_irrigation_daily_adjusted_run_time
  action:
  - data: {}
    entity_id: switch.irrigation_tap1
    service: switch.turn_on
  - delay:
      seconds: '{{states("sensor.smart_irrigation_daily_adjusted_run_time")}}'
  - data: {}
    entity_id: switch.irrigation_tap1
    service: switch.turn_off
  - data: {}
    service: smart_irrigation.reset_bucket

See more advanced examples in the Wiki.

Step 4: configuring optional settings

After setting up the component, you can use the options flow to configure the following:

Option	Description	Default
Lead time	Time in seconds to add to any irrigation. Very useful if your system needs to handle another task first, such as building up pressure.	0
Change percentage	Percentage to change adjusted run time by. For example, you want to run 80% of the calculated adjusted run time, enter 80 here. Or, if you want to run 150% of the calculated adjusted run time, enter 150.	100
Maximum duration	Maximum duration in seconds for any irrigation, including any lead_time. -1 means no maximum.	-1
Show units	If enabled, attributes values will show units. By default units will be hidden for attribute values.	False
Automatic refresh	By default, automatic refresh is enabled. Disabling it will require the user to call smart_irrigation.calculate_daily_adjusted_run_time manually.	True
Automatic refresh time	Specifies when to do the automatic refresh if enabled.	23:00
Initial update delay	Delay before first sensor update after reboot. This is useful if using sensors that do not have a status right after reboot.	30
Coastal	If the location you are tracking is situated on or adjacent to coast of a large land mass or anywhere else where air masses are influenced by a nearby water body, enable this setting.	False
Solar Radiation calculation	From v0.0.50 onwards, the component estimates solar radiation using temperature, which seems to be more accurate. If for whatever reason you wanted to revert back to the pre v0.0.50 behavior (which used a estimation of sun hours) disable this.	True

Example behavior in a week

This Wiki page provides insight into how this component should behave in certain weather conditions. With this you should be able to do a sanity check against your configuration and make sure everything is working correctly.

Available services

The component provides the following services:

Service	Description
smart_irrigation.reset_bucket	this service needs to be called after any irrigation so the bucket is reset to 0.
smart_irrigation.set_bucket	call this service to set the bucket to the value you provide. This service should only be used for debugging purposes.
smart_irrigation.calculate_daily_adjusted_run_time	calling this service results in the smart_irrigation.daily_adjusted_run_time entity and attributes to be updated right away.
smart_irrigation.calculate_hourly_adjusted_run_time	calling this service results in the smart_irrigation.hourly_adjusted_run_time entity and attributes to be updated right away.
smart_irrigation.enable_force_mode	Enables force mode. In this mode, smart_irrigation.daily_adjusted_run_time will also be set to the configured force mode duration.
smart_irrigation.disable_force_mode	Disables force mode. Normal operation resumes.

How this works

See the Wiki.

Getting Open Weather Map API key

Go to https://openweathermap.org and create an account. You can enter any company and purpose while creating an account. After creating your account, go to API Keys and get your key. If the key does not work right away, no worries. The email you should have received from OpenWeaterMap says it will be activated 'within the next couple of hours'. So if it does not work right away, be patient a bit.

Getting Monthly ET values

To get the monthly ET values use Rainmaster (US only), World Water & Climate Institute (worldwide) or another source that has this information for your area.

When entering the ET values in the configuration of this component, keep in mind that the component will expect inches or mm depending on the settings in Home Assistant (imperial vs metric system).

Using Rainmaster (US only)

Go to http://www.rainmaster.com/historicET.aspx and enter your 5-digit zipcode and click 'Find'. The values you are looking for are listed for each month in inch/day:

World Water & Climate Institute (International)

Go to http://wcatlas.iwmi.org/ and create an account. Once logged in, enter the locations you are interested in and click 'Submit'. Be sure to select N/S and E/W according to your coordinates:

The values you are looking for are in the last column (Penman ETo (mm/day)):