title | description | addedAt | pageClass |
---|---|---|---|
Datek 0402946 control via MQTT |
Integrate your Datek 0402946 via Zigbee2MQTT with whatever smart home infrastructure you are using without the vendor's bridge or gateway. |
2021-04-29 18:07:03 UTC |
device-page |
Model | 0402946 |
Vendor | Datek |
Description | Zigbee module for ID lock 150 |
Exposes | lock (state, lock_state), battery, pin_code, action, action_source_name, action_user, sound_volume, master_pin_mode, rfid_enable, relock_enabled, lock_mode, service_mode, linkquality |
Picture |
If pairing failed, try the followings:
- Make sure door are in open state
- Press and hold manual lock button and wait for 3 beeps
- Keypad in front lights up
- Type inn the Master PIN, then *, then 2, then *, then 0 Lock will now reset the Zigbee module and go to pairing mode
To retrieve the state, send a get
message to the device topic (zigbee2mqtt/DEVICE_FRIENDLY_NAME/get
) with the body {"pin_code":{"user":1}}
. To set, send a set
message to the device topic (zigbee2mqtt/DEVICE_FRIENDLY_NAME/set
) with the body {"pin_code":{"user":1,"pin_code":1234}}
. To clear a code, send a set
message with the body {"pin_code":{"user":1}}
ID LOCK 150 user manual Zigbee module user manual
How to use device type specific configuration
expose_pin
: Expose pin of this lock in the published payload (default false). The value must betrue
orfalse
The current state of this lock is in the published state under the state
property (value is LOCK
or UNLOCK
).
To control this lock publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set
with payload {"state": "LOCK"}
or {"state": "UNLOCK"}
.
To read the current state of this lock publish a message to topic zigbee2mqtt/FRIENDLY_NAME/get
with payload {"state": ""}
.
This lock exposes a lock state which can be found in the published state under the lock_state
property. It's not possible to read (/get
) or write (/set
) this value. The possible values are: not_fully_locked
, locked
, unlocked
.
Remaining battery in %, can take up to 24 hours before reported..
Value can be found in the published state on the battery
property.
It's not possible to read (/get
) or write (/set
) this value.
The minimal value is 0
and the maximum value is 100
.
The unit of this value is %
.
Can be set by publishing to zigbee2mqtt/FRIENDLY_NAME/set
with payload {"pin_code": {"user": VALUE, "user_type": VALUE, "user_enabled": VALUE, "pin_code": VALUE}}
To read (/get
) the value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/get
with payload {"pin_code": ""}
.
user
(numeric): User ID to set or clear the pincode foruser_type
(enum): Type of user, unrestricted: owner (default), (year|week)_day_schedule: user has ability to open lock based on specific time period, master: user has ability to both program and operate the door lock, non_access: user is recognized by the lock but does not have the ability to open the lock allowed values:unrestricted
,year_day_schedule
,week_day_schedule
,master
,non_access
user_enabled
(binary): Whether the user is enabled/disabled allowed values:true
orfalse
pin_code
(numeric): Pincode to set, set pincode to null to clear
Triggered action on the lock.
Value can be found in the published state on the action
property.
It's not possible to read (/get
) or write (/set
) this value.
The possible values are: unknown
, lock
, unlock
, lock_failure_invalid_pin_or_id
, lock_failure_invalid_schedule
, unlock_failure_invalid_pin_or_id
, unlock_failure_invalid_schedule
, one_touch_lock
, key_lock
, key_unlock
, auto_lock
, schedule_lock
, schedule_unlock
, manual_lock
, manual_unlock
, non_access_user_operational_event
.
Source of the triggered action on the lock.
Value can be found in the published state on the action_source_name
property.
It's not possible to read (/get
) or write (/set
) this value.
The possible values are: keypad
, rfid
, manual
, rf
.
ID of user that triggered the action on the lock.
Value can be found in the published state on the action_user
property.
It's not possible to read (/get
) or write (/set
) this value.
Sound volume of the lock.
Value can be found in the published state on the sound_volume
property.
To read (/get
) the value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/get
with payload {"sound_volume": ""}
.
To write (/set
) a value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set
with payload {"sound_volume": NEW_VALUE}
.
The possible values are: silent_mode
, low_volume
, high_volume
.
Allow Master PIN Unlock.
Value can be found in the published state on the master_pin_mode
property.
To read (/get
) the value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/get
with payload {"master_pin_mode": ""}
.
To write (/set
) a value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set
with payload {"master_pin_mode": NEW_VALUE}
.
If value equals true
master_pin_mode is ON, if false
OFF.
Allow RFID to Unlock.
Value can be found in the published state on the rfid_enable
property.
To read (/get
) the value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/get
with payload {"rfid_enable": ""}
.
To write (/set
) a value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set
with payload {"rfid_enable": NEW_VALUE}
.
If value equals true
rfid_enable is ON, if false
OFF.
Allow Auto Re-Lock.
Value can be found in the published state on the relock_enabled
property.
To read (/get
) the value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/get
with payload {"relock_enabled": ""}
.
To write (/set
) a value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set
with payload {"relock_enabled": NEW_VALUE}
.
If value equals true
relock_enabled is ON, if false
OFF.
Lock-Mode of the Lock.
Value can be found in the published state on the lock_mode
property.
To read (/get
) the value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/get
with payload {"lock_mode": ""}
.
To write (/set
) a value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set
with payload {"lock_mode": NEW_VALUE}
.
The possible values are: auto_off_away_off
, auto_on_away_off
, auto_off_away_on
, auto_on_away_on
.
Service Mode of the Lock.
Value can be found in the published state on the service_mode
property.
To read (/get
) the value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/get
with payload {"service_mode": ""}
.
To write (/set
) a value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set
with payload {"service_mode": NEW_VALUE}
.
The possible values are: deactivated
, random_pin_1x_use
, random_pin_24_hours
.
Link quality (signal strength).
Value can be found in the published state on the linkquality
property.
It's not possible to read (/get
) or write (/set
) this value.
The minimal value is 0
and the maximum value is 255
.
The unit of this value is lqi
.