-
Notifications
You must be signed in to change notification settings - Fork 0
/
mainsail.cfg
310 lines (280 loc) · 13.2 KB
/
mainsail.cfg
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
## Client klipper macro definitions
##
## Copyright (C) 2022 Alex Zellner <[email protected]>
##
## This file may be distributed under the terms of the GNU GPLv3 license
##
## !!! This file is read-only. Maybe the used editor indicates that. !!!
##
## Customization:
## 1) copy the gcode_macro _CLIENT_VARIABLE (see below) to your printer.cfg
## 2) remove the comment mark (#) from all lines
## 3) change any value in there to your needs
##
## Use the PAUSE macro direct in your M600:
## e.g. with a different park position front left and a minimal height of 50
## [gcode_macro M600]
## description: Filament change
## gcode: PAUSE X=10 Y=10 Z_MIN=50
## Z_MIN will park the toolhead at a minimum of 50 mm above to bed to make it easier for you to swap filament.
##
## Client variable macro for your printer.cfg
#[gcode_macro _CLIENT_VARIABLE]
#variable_use_custom_pos : False ; use custom park coordinates for x,y [True/False]
#variable_custom_park_x : 0.0 ; custom x position; value must be within your defined min and max of X
#variable_custom_park_y : 0.0 ; custom y position; value must be within your defined min and max of Y
#variable_custom_park_dz : 2.0 ; custom dz value; the value in mm to lift the nozzle when move to park position
#variable_retract : 1.0 ; the value to retract while PAUSE
#variable_cancel_retract : 5.0 ; the value to retract while CANCEL_PRINT
#variable_speed_retract : 35.0 ; retract speed in mm/s
#variable_unretract : 1.0 ; the value to unretract while RESUME
#variable_speed_unretract : 35.0 ; unretract speed in mm/s
#variable_speed_hop : 15.0 ; z move speed in mm/s
#variable_speed_move : 100.0 ; move speed in mm/s
#variable_park_at_cancel : False ; allow to move the toolhead to park while execute CANCEL_PRINT [True/False]
#variable_park_at_cancel_x : None ; different park position during CANCEL_PRINT [None/Position as Float]; park_at_cancel must be True
#variable_park_at_cancel_y : None ; different park position during CANCEL_PRINT [None/Position as Float]; park_at_cancel must be True
## !!! Caution [firmware_retraction] must be defined in the printer.cfg if you set use_fw_retract: True !!!
#variable_use_fw_retract : False ; use fw_retraction instead of the manual version [True/False]
#gcode:
[virtual_sdcard]
path: ~/printer_data/gcodes
on_error_gcode: CANCEL_PRINT
[pause_resume]
[display_status]
[gcode_macro SCREWS_CALCULATE]
gcode:
SCREWS_TILT_CALCULATE
#[gcode_macro G29]
#gcode:
# BED_MESH_CALIBRATE
#[gcode_macro M48]
#gcode:
# G1 Z5
# PROBE
# G1 Z5
# PROBE
# G1 Z5
# PROBE
# G1 Z5
# PROBE
# G1 Z5
# PROBE
# G1 Z20
[gcode_macro START_PRINT]
gcode:
G92 E0 ; Reset Extruder
{% set BED_TEMP = params.BED_TEMP|default(0)|float %}
{% set EXTRUDER_TEMP = params.EXTRUDER_TEMP|default(0)|float %}
M140 S{BED_TEMP} ;Start heating bed
G28 ; Home all axes
M190 S{BED_TEMP} ;Wait for bed to reach temp before proceeding
#M104 S{EXTRUDER_TEMP} ;Start heating extruder
M104 S165
SETUP_KAMP_MESHING DISPLAY_PARAMETERS=1 LED_ENABLE=1 FUZZ_ENABLE=1
BED_MESH_CALIBRATE ; Auto bed leveling
M104 S{EXTRUDER_TEMP} ;Start heating extruder
G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed
G1 X0.1 Y20 Z0.3 F5000.0 ; Move to start position
M109 S{EXTRUDER_TEMP} ;Wait for extruder to reach temp before proceeding
#G1 X0.1 Y200.0 Z0.3 F1500.0 E15 ; Draw the first line
#G1 X0.4 Y200.0 Z0.3 F5000.0 ; Move to side a little
#G1 X0.4 Y20 Z0.3 F1500.0 E30 ; Draw the second line
#G92 E0 ; Reset Extruder
#G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed
#G1 X5 Y20 Z0.3 F5000.0 ; Move over to prevent blob squish
#SETUP_VORON_PURGE
LINE_PURGE
[gcode_macro END_PRINT]
gcode:
LED_SUCCESS
{% set max_y = printer.toolhead.axis_maximum.y|float %}
# Move nozzle away from print while retracting
M83 ; Relative E
G91 ; Relative XYZ
G1 X-2 Y-2 Z+5 E-3 F300
G90 ; Absolute XYZ
M82 ; Absolute E
M104 S0 ; turn off temperature
M140 S0 ; turn off heatbed
M106 S0 ; Leave fan running to protect cooling ducts.
# Present print
G1 X0 Y210 F3000 ; present print
# Disable steppers
M84
[gcode_macro CANCEL_PRINT]
description: Cancel the actual running print
rename_existing: CANCEL_PRINT_BASE
gcode:
##### get user parameters or use default #####
{% set macro_found = True if printer['gcode_macro _CLIENT_VARIABLE'] is defined else False %}
{% set client = printer['gcode_macro _CLIENT_VARIABLE'] %}
{% set allow_park = False if not macro_found
else False if client.park_at_cancel is not defined
else True if client.park_at_cancel|lower == 'true'
else False %}
{% set retract = 5.0 if not macro_found else client.cancel_retract|default(5.0)|abs %}
##### define park position #####
{% set park_x = "" if not macro_found
else "" if client.park_at_cancel_x is not defined
else "X=" + client.park_at_cancel_x|string if client.park_at_cancel_x is not none %}
{% set park_y = "" if not macro_found
else "" if client.park_at_cancel_y is not defined
else "Y=" + client.park_at_cancel_y|string if client.park_at_cancel_y is not none %}
{% set custom_park = True if (park_x|length > 0 or park_y|length > 0) else False %}
##### end of definitions #####
{% if (custom_park or not printer.pause_resume.is_paused) and allow_park %} _TOOLHEAD_PARK_PAUSE_CANCEL {park_x} {park_y} {% endif %}
_CLIENT_RETRACT LENGTH={retract}
TURN_OFF_HEATERS
M106 S0
# clear pause_next_layer and pause_at_layer as preparation for next print
SET_PAUSE_NEXT_LAYER ENABLE=0
SET_PAUSE_AT_LAYER ENABLE=0 LAYER=0
CANCEL_PRINT_BASE
[gcode_macro PAUSE]
description: Pause the actual running print
rename_existing: PAUSE_BASE
gcode:
SET_GCODE_VARIABLE MACRO=RESUME VARIABLE=last_extruder_temp VALUE="{printer[printer.toolhead.extruder].target}"
PAUSE_BASE
_TOOLHEAD_PARK_PAUSE_CANCEL {rawparams}
[gcode_macro RESUME]
description: Resume the actual running print
rename_existing: RESUME_BASE
variable_last_extruder_temp: 0
gcode:
##### get user parameters or use default #####
{% set macro_found = True if printer['gcode_macro _CLIENT_VARIABLE'] is defined else False %}
{% set client = printer['gcode_macro _CLIENT_VARIABLE'] %}
{% set velocity = printer.configfile.settings.pause_resume.recover_velocity %}
{% set sp_move = velocity if not macro_found else client.speed_move|default(velocity) %}
##### end of definitions #####
M109 S{last_extruder_temp}
_CLIENT_EXTRUDE
RESUME_BASE VELOCITY={params.VELOCITY|default(sp_move)}
# Usage: SET_PAUSE_NEXT_LAYER [ENABLE=[0|1]] [MACRO=<name>]
[gcode_macro SET_PAUSE_NEXT_LAYER]
description: Enable a pause if the next layer is reached
gcode:
{% set pause_next_layer = printer['gcode_macro SET_PRINT_STATS_INFO'].pause_next_layer %}
{% set ENABLE = params.ENABLE | default(1) | int != 0 %}
{% set MACRO = params.MACRO | default(pause_next_layer.call, True) %}
SET_GCODE_VARIABLE MACRO=SET_PRINT_STATS_INFO VARIABLE=pause_next_layer VALUE="{{ 'enable': ENABLE, 'call': MACRO }}"
# Usage: SET_PAUSE_AT_LAYER [ENABLE=[0|1]] [LAYER=<number>] [MACRO=<name>]
[gcode_macro SET_PAUSE_AT_LAYER]
description: Enable/disable a pause if a given layer number is reached
gcode:
{% set pause_at_layer = printer['gcode_macro SET_PRINT_STATS_INFO'].pause_at_layer %}
{% set ENABLE = params.ENABLE | int != 0 if params.ENABLE is defined
else params.LAYER is defined %}
{% set LAYER = params.LAYER | default(pause_at_layer.layer) | int %}
{% set MACRO = params.MACRO | default(pause_at_layer.call, True) %}
SET_GCODE_VARIABLE MACRO=SET_PRINT_STATS_INFO VARIABLE=pause_at_layer VALUE="{{ 'enable': ENABLE, 'layer': LAYER, 'call': MACRO }}"
# Usage: SET_PRINT_STATS_INFO [TOTAL_LAYER=<total_layer_count>] [CURRENT_LAYER= <current_layer>]
[gcode_macro SET_PRINT_STATS_INFO]
rename_existing: SET_PRINT_STATS_INFO_BASE
description: Overwrite, to get pause_next_layer and pause_at_layer feature
variable_pause_next_layer: { 'enable': False, 'call': "PAUSE" }
variable_pause_at_layer : { 'enable': False, 'layer': 0, 'call': "PAUSE" }
gcode:
{% if pause_next_layer.enable %}
{action_respond_info("%s, forced by pause_next_layer" % pause_next_layer.call)}
{pause_next_layer.call} ; execute the given gcode to pause, should be either M600 or PAUSE
SET_PAUSE_NEXT_LAYER ENABLE=0
{% elif pause_at_layer.enable and params.CURRENT_LAYER is defined and params.CURRENT_LAYER|int == pause_at_layer.layer %}
{action_respond_info("%s, forced by pause_at_layer [%d]" % (pause_at_layer.call, pause_at_layer.layer))}
{pause_at_layer.call} ; execute the given gcode to pause, should be either M600 or PAUSE
SET_PAUSE_AT_LAYER ENABLE=0
{% endif %}
SET_PRINT_STATS_INFO_BASE {rawparams}
##### internal use #####
[gcode_macro _TOOLHEAD_PARK_PAUSE_CANCEL]
description: Helper: park toolhead used in PAUSE and CANCEL_PRINT
gcode:
##### get user parameters or use default #####
{% set macro_found = True if printer['gcode_macro _CLIENT_VARIABLE'] is defined else False %}
{% set client = printer['gcode_macro _CLIENT_VARIABLE'] %}
{% set velocity = printer.configfile.settings.pause_resume.recover_velocity %}
{% set use_custom = False if not macro_found
else False if client.use_custom_pos is not defined
else True if client.use_custom_pos|lower == 'true'
else False %}
{% set custom_park_x = 0.0 if not macro_found else client.custom_park_x|default(0.0) %}
{% set custom_park_y = 0.0 if not macro_found else client.custom_park_y|default(0.0) %}
{% set park_dz = 2.0 if not macro_found else client.custom_park_dz|default(2.0)|abs %}
{% set sp_hop = 900 if not macro_found else client.speed_hop|default(15) * 60 %}
{% set sp_move = velocity * 60 if not macro_found else client.speed_move|default(velocity) * 60 %}
##### get config and toolhead values #####
{% set origin = printer.gcode_move.homing_origin %}
{% set act = printer.gcode_move.gcode_position %}
{% set max = printer.toolhead.axis_maximum %}
{% set cone = printer.toolhead.cone_start_z|default(max.z) %} ; height as long the toolhead can reach max and min of an delta
{% set round_bed = True if printer.configfile.settings.printer.kinematics is in ['delta','polar','rotary_delta','winch']
else False %}
##### define park position #####
{% set z_min = params.Z_MIN|default(0)|float %}
{% set z_park = [[(act.z + park_dz), z_min]|max, (max.z - origin.z)]|min %}
{% set x_park = params.X if params.X is defined
else custom_park_x if use_custom
else 0.0 if round_bed
else (max.x - 5.0) %}
{% set y_park = params.Y if params.Y is defined
else custom_park_y if use_custom
else (max.y - 5.0) if round_bed and z_park < cone
else 0.0 if round_bed
else (max.y - 5.0) %}
##### end of definitions #####
_CLIENT_RETRACT
{% if "xyz" in printer.toolhead.homed_axes %}
G90
G1 Z{z_park} F{sp_hop}
G1 X{x_park} Y{y_park} F{sp_move}
{% if not printer.gcode_move.absolute_coordinates %} G91 {% endif %}
{% else %}
{action_respond_info("Printer not homed")}
{% endif %}
[gcode_macro _CLIENT_EXTRUDE]
description: Extrudes, if the extruder is hot enough
gcode:
{% set macro_found = True if printer['gcode_macro _CLIENT_VARIABLE'] is defined else False %}
{% set client = printer['gcode_macro _CLIENT_VARIABLE'] %}
{% set use_fw_retract = False if not macro_found
else False if client.use_fw_retract is not defined
else True if client.use_fw_retract|lower == 'true' and printer.firmware_retraction is defined
else False %}
{% set length = (params.LENGTH|float) if params.LENGTH is defined
else 1.0 if not macro_found
else client.unretract|default(1.0) %}
{% set speed = params.SPEED if params.SPEED is defined
else 35 if not macro_found
else client.speed_unretract|default(35) %}
{% set absolute_extrude = printer.gcode_move.absolute_extrude %}
{% if printer.extruder.can_extrude %}
{% if use_fw_retract %}
{% if length < 0 %}
G10
{% else %}
G11
{% endif %}
{% else %}
M83
G1 E{length} F{(speed|float|abs) * 60}
{% if absolute_extrude %}
M82
{% endif %}
{% endif %}
{% else %}
{action_respond_info("Extruder not hot enough")}
{% endif %}
[gcode_macro _CLIENT_RETRACT]
description: Retracts, if the extruder is hot enough
gcode:
{% set macro_found = True if printer['gcode_macro _CLIENT_VARIABLE'] is defined else False %}
{% set client = printer['gcode_macro _CLIENT_VARIABLE'] %}
{% set length = (params.LENGTH|float) if params.LENGTH is defined
else 1.0 if not macro_found
else client.retract|default(1.0) %}
{% set speed = params.SPEED if params.SPEED is defined
else 35 if not macro_found
else client.speed_retract|default(35) %}
_CLIENT_EXTRUDE LENGTH=-{length|float|abs} SPEED={speed|float|abs}