forked from larsbrinkhoff/httptunnel
-
Notifications
You must be signed in to change notification settings - Fork 0
/
HACKING
96 lines (70 loc) · 2.86 KB
/
HACKING
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
General idea.
FIXME: client, server. HTTP.
All HTTP requests are made by the client, htc, and are served by the
server, hts.
Data is sent to the server using HTTP PUT requests. These have a
Content-Length header line, which is obeyed strictly if the --strict
option is used. tunnel.c provides a nice interface to the
complexities of HTTP requests. See tunnel.h for information about the
programming interface.
In the other direction, data is transferred using HTTP GET requests.
Proxy buffering.
Some proxies buffer data in HTTP PUT or POST requests. FIXME: explain
why this is a problem and how it is solved.
Debugging.
To enable debugging code, use --enable-debug with 'configure'. This
will make htc and hts recognize a --debug switch.
--debug 0 - no messages whatsoever
--debug 1 - log_notice () - important events
--debug 2 - log_error () - unexpected errors
--debug 3 - log_debug () - sparse debugging
--debug 4 - log_verbose () - debugging in innner loops
--debug 5 - log_annoying () - system calls and more
Without --enable-debug, log_notice() and log_error() will log using
syslog() with level LOG_NOTICE and LOG_ERROR, respectively.
log_debug(), log_verbose(), and log_annoying() will be disabled.
Some notes about the protocol.
The data sent in HTTP requests is in itself formatted according to a
simple protocol. This is needed becase some HTTP proxy servers buffer
data before sending it to its final destination.
There are seven different requests in this protocol, and there are
two types of requests. Requests with the 0x40 bit set consists of
just one byte, with no additional data. Requests with the 0x40 bit
clear have a two-byte length field and a variable length data field.
TUNNEL_OPEN
01 xx xx yy...
xx xx = length of auth data
yy... = auth data
OPEN is the initial request. For now, auth data is unused,
but should be used for authentication.
TUNNEL_DATA
02 xx xx yy...
xx xx = lenth of data
yy... = data
DATA is the one and only way to send data.
TUNNEL_PADDING
03 xx xx yy...
xx xx = lenth of padding
yy... = padding (will be discarded)
PADDING exists only to allow padding the HTTP data. This is
needed for HTTP proxies that buffer data.
TUNNEL_ERROR
04 xx xx yy...
xx xx = length of error message
yy... = error message
Report an error to the peer.
TUNNEL_PAD1
45
PAD1 can be used for padding when a PADDING request would be
too long with regard to Content-Length. PADDING should always
be preferred, though, because it's easier for the recipent to
parse one large request than many small.
TUNNEL_CLOSE
46
CLOSE is used to close the tunnel. No more data can be sent
after this request is issued, except for a TUNNEL_DISCONNECT.
TUNNEL_DISCONNECT
47
DISCONNECT is used to close the connection temporarily,
probably because Content-Length - 1 number of bytes of data
has been sent in the HTTP request.