deploy: 7d6a75f

_sources/source/projects/ad5754r_iio/ad5754r_iio.rst.txt

@@ -0,0 +1,131 @@
+AD5754R/CN0586 IIO Application
+""""""""""""""""""""""""""""""
+
+==================
+Supported Hardware
+==================
+
+**Supported Devices:**
+
+* `AD5754R <https://www.analog.com/en/products/ad5754r.html>`_ 
+
+**Supported Evaluation Boards:**
+
+* `EVAL-CN0586-ARDZ <https://www.analog.com/en/resources/reference-designs/circuits-from-the-lab/cn0586.html#rd-overview>`_
+* `EVAL-AD5754R <https://www.analog.com/en/resources/evaluation-hardware-and-software/evaluation-boards-kits/eval-ad5754r.html?`_
+
+**Supported Carrier Boards:**
+
+* SDP-K1 With `Mbed Platform <https://os.mbed.com/platforms/SDP_K1/>`_ 
+
+============
+Introduction
+============
+
+This page gives an overview of using the ARM platforms supported (Mbed) 
+firmware example with Analog Devices EVAL-CN0586-ARDZ and EVAL-AD5754R Evaluation boards and SDP-K1 controller board. 
+This example code leverages the ADI developed IIO (Industrial Input Output) ecosystem to 
+evaluate the AD5754R/CN0586 device by providing a device debug and data capture support.
+The code provides support for MBED platform, using the SDP-K1 controller board.
+
+The build guide for the Mbed platform can be found in the further sections.
+
+   .. image:: /source/tinyiiod/app_interface.png
+      :width: 350
+
+The interface used for communicating with PC based IIO clients is either Virtual Serial Or UART. 
+IIO Firmware leverages the ADI created no-os and platform driver software layers
+to communicates with IIO device.
+
+.. SDP-K1 Mbed Section
+
+.. include:: /source/tinyiiod/sdp_k1_mbed.rst
+
+.. Useful links Section
+
+.. include:: /source/useful_links.rst
+
+====================
+Hardware Connections
+====================
+
+Required: SDP-K1 (or alternative Mbed enabled controller board), EVAL-AD5754R board or EVAL-CN0586-ARDZ board,
+and USB cable.
+
+When using the EVAL-CN0586-ARDZ, connect the EVAL-CN0586 board to the controller board by stacking the CN0586's digital interface pins 
+onto the controller board's Arduino Uno V3 header.
+Connect controller board to the PC using the USB cable. 
+
+   .. image:: /source/projects/ad5754r_iio/ad5754r_interface_diagram.png
+      :width: 600
+
+When using the EVAL-AD5754R, make the connections as follows using jumper wires:
+
++-------------+---------------+
+| SDP-K1      |  EVAL-AD5754R |
++-------------+---------------+
+| D13         |  J8 Pin 9     |
++-------------+---------------+
+| D12         |  J8 Pin 1     |
++-------------+---------------+
+| D11         |  J8 Pin 7     |
++-------------+---------------+
+| D10         |  J8 Pin 10    |
++-------------+---------------+
+| D6          |  J8 Pin 7     |
++-------------+---------------+
+| D4          |  J8 Pin 4     |
++-------------+---------------+
+| DGND        |  J8 Pin 3     |
++-------------+---------------+
+
+====================================
+EVAL-CN0586-ARDZ Evaluation Firmware
+====================================
+
+By default, the firmware exposes two IIO Devices: "ad5754r" and "cn0586". The "cn0586" IIO device allows configuring the output's state,
+range and voltage level. For a more granular access to the DAC, the "ad5754r" IIO device can be used to configure 
+IIO attributes tied to the DAC's bitfields, or even perform direct register reads and writes.
+
+================================
+EVAL-AD5754R Evaluation Firmware 
+================================
+
+To build the firmware to use with EVAL-AD5754R, comment the "DEV_CN0586" macro definition in app_config.h. When using the 
+EVAL-AD5754R, configure the jumpers to allow the SDP-K1 (or any other Mbed enabled controller board) to
+control the digital interface. Refer to the Evaluation Board user guide for the jumper configurations.
+
+===============
+Jumper Settings
+===============
+
+SDP-K1 :
+
+Connect the VIO_ADJUST jumper on the SDP-K1 to 3.3V position 
+to drive SDP-K1 GPIOs at 3.3V
+
+**EVAL-AD5754R and EVAL-CN0586-ARDZ:**
+
+Please refer to the user guide for the jumper connections on the Evaluation Boards.
+
+.. Communication Interface section:
+
+.. include:: /source/hardware/comm_interface.rst
+
+.. Project Build Section:
+    
+.. include:: /source/build/project_build.rst
+
+.. IIO Ecosystem Section:
+    
+.. include:: /source/tinyiiod/iio_ecosystem.rst
+
+.. IIO Firmware Structure
+
+.. include:: /source/tinyiiod/iio_firmware_structure.rst
+
+=======
+Support
+=======
+
+Feel free to ask questions in the `EngineerZone <https://ez.analog.com/data_converters>`_

_sources/source/projects/index.rst.txt

@@ -12,6 +12,7 @@ Firmware Applications
    /source/projects/ad4170_iio/ad4170_iio.rst
    /source/projects/ad4696_iio/ad4696_iio.rst
    /source/projects/ad559xr_console/ad559xr_console.rst
+   /source/projects/ad5754r_iio/ad5754r_iio.rst
    /source/projects/ad5770r_iio/ad5770r_console.rst
    /source/projects/ad579x_iio/ad579x_iio.rst
    /source/projects/ad590_console/ad590_console.rst