PlutoSDR: Prepare for v0.33 release

Submodule linux 6edc6cd..b05d164:
  > arm: configs: zynq_[pluto|m2k]_defconfig: Add DM9601 USB Ethernet driver
  > drivers: frequency: adf5355: add REG10 write
  > drivers:frequency:adf5355: add delay for init seq
  > iio: frequency: adf5355: Fix potential locking issue for PFD > 75MHz
  > Documentation/devicetree/bindings/iio/frequency/adf5355: Update for ADF5356
  > iio: frequency: adf5355: Add support for ADF5356
  > iio: amplifiers: ad8366: Update device support
  > iio: adc: ad9081: PRBS and partial eyescan support via debugfs
  > iio: adc: ad9081: Support for CBUS direct_reg_access
  > iio: adrv9002: misc improvements
  > iio: adrv9002: support tx only profiles
  > arch: arm: boot: dts: de10_nano_cn0540: Use decimal format for i2c address
  > arch: arm: boot: dts: de10_nano.dtsi: Rename altera spi node name
  > arch: arm: boot: dts: Replace spi-engine node names
  > iio: adrv9002: also reset orx state
  > iio: adrv9002: improve init failure handling
  > dt-bindings: clock: ad9545: Fast ACQ trigger mode
  > clk: ad9545: Add fast acq trigger mode to dt
  > iio: adrv9002: fix possible deadlock
  > iio: jesd204: axi_adxcvr: Support for physical layer PRBS
  > arm64: dts: adi-ad9081-fmc-ebz.dtsi: Fix JESD204 use case
  > iio: adc: ad7124: allow more than 8 channels
  > iio: adrv9002: fix possible data races
  > iio: adrv9002: support near end loopback
  > clk: ad9545: Fix source selection
  > dt-bindings: clock: ad9545: Add fast acquisition
  > clk: ad9545: Add fast acquisition
  > iio: adc: ad9081: For R2 and later don't touch tpl_buf_protect_en
  > microblaze: dts: vcu118_ad9081.dts: Add IRQB gpios
  > iio: adc: ad9081: Add optional JRX Link watchdog
  > iio: adc: ad9081: Update debugfs status info (JRX TPL PHASE DIFFERENCE)
  > iio: adc: ad9081: Prepare for IRQB handling
  > iio: adc: ad9081: Update API to Version 1.1.0
  > iio: adrv9002: improve tx interface tuning
  > iio: adrv9002: use prbs7 for tx tuning
  > iio: adrv9002: fix loading low rate profiles
  > iio: adrv9002: export Orx gain in dBs
  > iio: adrv9002: api: move min/max Orx indexes
  > iio: adrv9002: support orx tracking cal
  > clk: ad9545: Fix recalc_rate
  > microblaze: dts: vcu118_ad9081_204c_txmode_[10|23]_rxmode_[11|25]: Set CTLE
  > iio: adc: ad9081: Add dt poperty to configure the CTLE filer.
  > iio: adc: ad9081: Toggle link enable around jesd_rx_calibrate_204c
  > iio: adc: ad9081: Add jesd_rx_calibrate_204c to MCS step 20
  > iio : frequency: ad9528: Fix JESD204 FSM reinit bug
  > iio : frequency: hmc7044: Fix JESD204 FSM reinit bug
  > microblaze: dts: vcu118_ad9081_204c_txmode_23_rxmode_25: Add TPL phase adj
  > microblaze: dts: adi-ad9081-fmc-ebz.dtsi: Fix JESD204 use case
  > microblaze: dts: vcu118_ad9081_204c_txmode_23_rxmode_25: Add device_clk
  > microblaze: dts: vcu118_ad9081.dts: Fix mode - requires QPLL on RX
  > iio: adc: ad9081: Support for FDDC, CDDC 6dB digital gain
  > arch: arm64: dts: Change SW0 linux code to  SW_LINEIN_INSERT
  > clk: ad9545: Add errors for missing properties
  > dt-bindings: clock: ad9545: Add source profiles
  > dt-bindings: clock: ad9545: Bindings cleanup
  > clock: ad9545: Add reference priorities
  > iio: frequency: cf_axi_dds: Roundup JESD204 NP always to the next pow2
  > iio: adc: ad9361: Fix rssi_gain_step_error DEVICE_ATTR mode
  > microblaze: boot: dts: Style checkpatch fixes - no functional changes
  > iio: adc: ad9081: Support for SPI_3WIRE and SPI_LSB_FIRST
  > dts: vcu118_quad_ad9081_204b_txmode_X_rxmode_Y_onchip_pll_revc: Add internal PLL use cases
  > dts: vcu118_quad_ad9081_204c_txmode_29_rxmode_24_revc: New NP=12 use case
  > dts: vcu118_quad_ad9081_204c_txmode_23_rxmode_25_revc: New NP=12 use case
  > iio: frequency: adf4371: Add option to power down the chip if not used
  > clk: ad9545: Allow uHz loop bw.
  > dt-bindings: clock: ad9545: Change loop bw doc
  > iio: adc: adrv9009: Fix typo in calibrate_fhm_en attribute
  > Revert "clocksource/drivers/cadence-ttc: Use ttc driver as platform driver"
  > iio: adc: adrv9009: Apply initial tx1/2_atten_ctrl_pin settings
  > ci: checkpatch: Replace python-git to python-git-doc
  > clk: axi-clkgen: Don't display error when -EPROBE_DEFER
  > arm: dts: zynq-zed-adrv9002 -> zynq-zed-adv7511-adrv9002
  > arm: dts: adrv9002: Add support for ZC706
  > arm: dts: adrv9002: Move common zynq-adrv9002 definitions to .dtsi
  > dts: zynq-zc706-adv7511-fmcomms11: ADXCVR TX use AD9625-DIVCLK
  > iio: adc: ad9467: AD9625 add DIVCLK CCF clock provider support
  > include: linux: clk: clkscale.h: Make sure div can never be zero
  > iio: adc: ad9371: force state of the TEST pin
  > iio: adc: ad9371: make use of devm_clk_get_optional
  > iio: adc: ad9371: add support for TX PRBS
  > iio: adc: ad9371: add support for PRBS error injection
  > iio: adc: ad9371: add PLL lock status debugfs entry
  > iio: adc: ad9371: enable sysref clocks if defined
  > iio: adc: ad9371: drop redundant error messages
  > drivers/iio/adc/mykonos: silent verbose debug messages
  > iio: adc: ad9081: Fix nco_frequency_available reading for bypassed fddc
  > iio: dac: ad5446: Add AD5542 spi id
  > staging: iio: frequency: ad9834: Fix typo in comment
  > drivers:iio:dac:ad5686: Fix segmentation fault
  > iio: adrv9002: add new kconfig options
  > iio: adc: adrv9009: Fix obsRxChannelsEnable clobbering in stitching mode
  > arch: dts: adrv9002: add orx support
  > iio: adrv9002: support Orx
  > iio: adc: ad9081: Avoid JTX link disable sequences
  > microblaze: dts: vcu118_ad9081_204c_txmode_24_rxmode_26_lr_24_75Gbps: Np 12 use case with high lane rate
  > microblaze: dts: vcu118_ad9081_204c_txmode_23_rxmode_25_lr_24_75Gbps: Np 12 use case with high lane rate
  > microblaze: dts: vcu118_ad9081_204c_txmode_23_rxmode_25: Np 12 use case
  > microblaze: dts: vcu118_ad9081_204c_txmode_10_rxmode_11_lr_24_75Gbps: Np 16 use case with high lane rate
  > microblaze: dts: vcu118_ad9081_204c_txmode_10_rxmode_11: 204C use case
  > arm: dts: Add AD9081-FMC-EBZ + Arria 10 SoC Development Kit support NP=12 case
  > iio/adc/adrv9009:  Fix octets per frame calculation for NP=12 case
  > arm: zynq-zc706-adv7511-ad9081-np12: NP12 devicetree
  > iio: jesd204: axi_jesd204_[rx|tx]: Add info print upon probe
  > iio: jesd204: axi_jesd204_[rx|tx]: Add support for NP=12 modes
  > clk: ad9545: Fix r-div write
  > arm: dts: adi-adrv9009.dtsi: OBS-Rx use JESD204 M=2
  > iio: jesd204: axi_jesd204_[rx|tx]: Avoid unbalanced clock disable (TEMP)
  > iio: jesd204: axi_jesd204_[rx|tx]: Fix potential out of spec SERDES PLL
  > arch: dts: zynq-zed-adrv9002: Enable HDMI output
  > iio: adrv9002: support reading profile_config
  > arch: dts: adi-fmcomms8.dtsi: Chan 1,3,6,7,8,9 are terminated for LVPCL
  > arch: dts: fix fmcomms8 master device assignments by name
  > ci: replace python- deps with python3- deps
  > clk: axi-clkgen: fix or operator; use logical vs bitwise or
  > iio: jesd204: axi_adxcvr: Fix log level in probe defer information
  > Revert "iio: axi_adxcvr: print warning on set_rate in adxcvr_enforce_settings()"
  > iio: adc: adrv9009_conv: In RX only operation skip configure DAC TPL
  > zynq-zed-adrv9002-rx2tx2.dts: Fix hdl project tag
  > iio: adrv9002: remove B0 define
  > iio: adrv9002: add full path for include directories
  > arm64: dts: Add ADRV9009-ZU11EG Multi-SoM sync device trees (No FMCOMMS8)
  > iio: adrv9002: remove duplicated define
  > iio: adrv9002: add support for c0 HW revision
  > hwmon: ltc2945: fix private data reference
  > arm64: dts: zynqmp-zcu102-rev10-ad9082-m4-l8.dts: Add AD9082-FMCA-EBZ dt
  > iio: adrv9002: fix irq handling
  > iio: dac: ad5766: add driver support for AD5766
  > Documentation/ABI/testing: Add documentation for AD5766 new ABI
  > dt-bindings: iio: dac: AD5766 yaml documentation
  > dts: AD9081-FMCA-EBZ: Consider the VCXO=100.00 MHz the default
  > iio: frequency: ad916x: Add SPDX-License-Identifier: GPL-2.0
  > iio: adc: talise: Add SPDX-License-Identifier: GPL-2.0
  > iio: adc: mykonos: Add SPDX-License-Identifier: GPL-2.0
  > microblaze: adi_mb_defconfig: Update for 5.4 and sync with Xilinx
  > iio: adrv9002: remove unused API's
  > mtd: spi-nor: Add support for disable broken flash locking
  > mtd: spi-nor: don't run SFDP for Zynq QSPI
  > iio: adrv9002: remove adrv9002_init_data.c
  > arm{64}: config: Add adrv9002 default profiles
  > firmware: adrv9002: add default profiles
  > iio: adrv9002: Load default profiles from firmware
  > iio: adc: ad7768: Add filter type attribute
  > iio: adc: ad7768: Update sampling frequency routine
  > iio: adc: ad7768: Add power mode attribute
  > iio: adc: ad7768: Add _set_clk_divs() function
  > iio: adc: ad7768: Add spi sync function
  > arch: arm: boot: dts: Add support for cora and ad7768
  > arch: arm: boot: dts: Add support for zed with ad7768 and axi_adc
  > iio: adc: ad7768: Add axi_adc support
  > arm: dts: zynq-zc702.dtsi: Add missing spi-max-frequency property
  > iio: adrv9002: Fix debugfs AGC parameter
  > iio: adrv9002: Improve device setup error path
  > iio: adrv9002: disable axi core before device setup
  > iio: adrv9002: validate ssi interface before device setup
  > iio: adrv9002: remove `adrv9002_axi_ssi_type_get()`
  > iio: adrv9002: save axi interface type at startup
  > iio: adrv9002: minor improvement on `adrv9002_cleanup()`
  > iio: adrv9002: call `adrv9002_init()` on debugfs
  > iio: adrv9002: remove `adrv9002_intf_tuning_unlocked()`
  > iio: adrv9002: centralize device initialization
  > iio: frequency: adf4371: Keep RF8 ports disabled
  > mtd: spi-nor: spi-nor: Fix SPI-NOR-UniqueID printing
  > arch: arm: re-enable uevent helper for busybox systems
  > Revert "clk: fixed-factor: Don't register fixed factor clk until parent clk is registered"
  > clk: walk orphan list on clock provider registration
  > microblaze: dts: Update model strings to reflect board and carrier
  > microblaze: dts: vc707: Update for Kernel v5.4 Vivado v2020.1
  > microblaze: dts: kcu105: Update for Kernel v5.4 Vivado v2020.1
  > microblaze: dts: kc705: Update for Kernel v5.4 Vivado v2020.1
  > arm: dts: Add AD9081-FMC-EBZ + Arria 10 SoC Development Kit support
  > usb: chipidea: Hook up ULPI support
  > clk: ad9545: Add support for n-shot
  > clk: introduce clk_set_nshot and clk_get_nshot
  > arch: microblaze: dts: vcu118: Update for Kernel v5.4 Vivado v2020.1
  > arch: zynq-coraz7s.dtsi: disable second CPU vs deleting node
  > arch: fix various warnings with device-trees
  > ci: remove old dtb-build patches mechanism
  > ci: update build for ADI drivers that should be built
  > spi-nor: cadence-quadspi: fix __aeabi_ldivmod compiler error
  > Revert "xilinx: Add a github template telling people to not use pull requests there"
  > jesd204: sysfs: add explicit fall-through
  > navassa: fix ISO C90 compiler warning
  > navassa: add missing break statements
  > iio: frequency: hmc7044: Improve the pfd1 calculation
  > iio: adc: ad9371: Fix temp sensor readings
  > iio: adc: mykonos: mykonos_gpio: Silent verbose debug messages
  > iio: adis16480: Limit spi max speed in burst mode
  > Revert "net: macb: Avoid probe error if more than one phy is available"
  > arch: arm64: adrv9009-zu11eg: fix spi dt node warnings
  > arch: arm: zynq-zc706-adv7511.dtsi: add @39 addr to adv7511 node
  > ci: update to sync adi-5.4.0 and rpi-5.4.y
  > net: phy: adin-t1l: update driver to 5.4 APIs
  > pwm: pwm-axi-pwmgen: update apply hook to new kernel
  > net: phy: adin-t1l: remove adin-compat.h
  > clk: ad9545: up regmap_config.use_single_rw
  > arch: run savedefconfig on all ADI defconfigs
  > Merge remote-tracking branch 'adi/master' into master-xilinx-v2020.1
  > media: axi-hdmi-rx: Initialize bus_type
  > media: axi-hdmi-rx: Provide device_caps in struct video_device
  > media/platform/axi-hdmi-rx: Announce GPLv2 module license
  > drm: adi_axi_hdmi: Fix fbdev interface not working
  > sound/soc/adi/axi-spdif.c: Support programmable master clock
  > drm: axi_hdmi_encoder.c: Add missing drm_print.h include
  > Merge remote-tracking branch 'adi/master' into master-xilinx-v2020.1
  > jesd204: fix & handle switch implicit fall-through
  > [media] adv7511-v4l2: remove XYLON_LOGICVC_INTG
  > iio: ad9081: fix potential invalid error code
  > ci,build: add new dts to dtb_build_test exception
  > Revert "media: drivers: media: i2c: don't enable if CONFIG_DRM_I2C_ADV7511=n"
  > [media] adv7511: Add support for the Power Down GPIO.
  > [media] adv7511: remove omitted memcpy() for pdata
  > [media] adv7511: Setup the timing generator according to the selected mode
  > ci,travis: update ignore build for branch adi-5.4.0
  > MAINTAINERS: remove hmc prefixed drivers
  > drivers/media/i2c/adv7511: Differentiate the adv7511-v4l2 driver by the adv7511-drm driver.
  > usb: chipidea: reset to upstream version
  > Revert "net: macb: disable gigabit for MII & RMII modes"
  > [media] adv7604: remove duplicate isr handler
  > sound: soc: adrv936x_box: rework driver to new kernel
  > [media] imageon-bridge: rework bridge notifier to new format
  > [media] axi-hdmi-rx: rework bridge notifier to new format
  > iio: logic: m2k-fabric: rework GPIO code to new framework
  > iio: cf_axi_dds: fix function type
  > iio: frequency: m2k-dac: fix match function type
  > misc: mathworks: fix mathworks_ip_mmap_fault() return type
  > media: addi9036: V4L2_MBUS_CSI2 -> V4L2_MBUS_CSI2_DPHY
  > drm: adi_axi_hdmi: update driver to newer framework [WIP]
  > drm: adi_axi_hdmi: remove drm_plane_helper_disable() call
  > drm: adi_axi_hdmi: add includes required to build in newer kernels
  > clk: clk-adjustable-rate: remove CLK_IS_BASIC flag
  > ci,travis: remove patches for dt build test
  > Merge tag 'xilinx-v2020.1' into master-xilinx-v2020.1
  > arch: arm64: adrv9009-zu11eg: Use the iio adm1177 driver
  > iio: adc: adm1177: Make a distinction between the hwmon and iio versions
  > ci: stop auto-sync-ing altera_4.14 & adi-iio branches
  > jesd204: fsm: always start state transition from top-level device
  > iio: adc: ad7124: move chip ID & name on the chip_info table
  > jesd204: fsm: remove inputs field
  > jesd204: fsm: rename jdev -> jdev_it in propagation
  > jesd204: fsm: set error on the connection and jdev object if cb fails
  > jesd204: add connection simple unique IDs
  > jesd204: fsm: don't get/put kref too many times
  > jesd204: fsm: don't decrease refcounts on error in __jesd204_fsm()
  > jesd204: fsm: return DEFER in initialize_cb if no link_idx found
  > jesd204: fsm: fix validation of connection link_idx
  > jesd204: fsm: fix busy-flags handling and group init links with start links
  > jesd204: fsm: handle memory free on each call of jesd204_fsm_table()
  > jesd204: fsm: remove empty line
  > jesd204: fsm: clear error current state is DONT_CARE
  > ci: check that all device-trees have an hdl_project tag
  > iio: dac: ad5592r: localize locks only where needed in ad5592r_read_raw()
  > iio: dac: ad5592r: un-indent code-block for scale read
  > iio: dac: ad5592r: fix unbalanced mutex unlocks in ad5592r_read_raw()
  > iio: dac: ad5592r-base: Replace indio_dev->mlock with own device lock

Submodule hdl 847f0f2..061d024:
  > axi_adrv9001: Quartus 19.3 updates
  > axi_adrv9001: Double sync control lines between interface 1 and 2
  > axi_ad9361: Update constraints in case TDD is disabled
  > adrv9001/zcu102/cmos: Loosen up clock skew constraints to match LVDS settings
  > fmcomms2/zed: Disable unused TDD to save space and timing
  > axi_adrv9001: Fix channel 3 for Tx1 in DMA mode
  > axi_adrv9001: rx: calculate ramp value based on received value
  > axi_adrv9001: Let gate signals have initial value, useful for simulation
  > axi_adrv9001: Add status bit for Tx clocking
  > axi_adrv9001:rx: Add reset to link layer
  > axi_adrv9001:rx:phy: do not generate valid while in reset
  > library/common/up_tdd_cntrl: Make address generic
  > adrv9001/zcu102: Run postRoutePhysOpt to close Rx1 to Rx2 path timing
  > adrv9001/common: Run DMAs @ 100MHz
  > axi_adrv9001: Add opt-in synthesis parameters
  > axi_adrv9001: Use global clocks for divided down clock
  > ad_pnmon: Fix zero checking when valid not constant
  > axi_adrv9001:axi_adrv9001_rx_channel: fix ramp signal checking
  > ad_tdd_control: Avoid single pulses if tx_only or rx_only
  > ad_tdd_control: Fix rx/tx only behavior
  > adrv9001/zed: Connect TDD sync to PMOD JA1
  > common/up_tdd_cntrl: Fix read data when read is idle
  > adrv9001/zcu102: Add TDD sync to PMOD0 J55.1
  > adrv9001/common: Export TDD mode signal
  > axi_adrv9001: Export TDD mode
  > adrv9001/zed: Add TDD support
  > adrv9001/zcu102: Add TDD support
  > axi_adrv9001: Add TDD support
  > adrv9009zu11eg:fmcomms8: Fix lane swapping for TX channels 0 and 1 on the FMCOMMS8
  > fmcomms8: zcu102: Fix lane swapping
  > daq3:zcu102: Connect overflow pins for the AD9680 TPL
  > Revert "intel: Update projects to use ad_iobuf instead of ALT_IOBUF"
  > de10nano: Add hps_conv_usb_n signal to stabilize UART lines
  > axi_hdmi_tx: Remove deprecated constraint
  > adv7513_de10nano: Fix gpio_bd assignments
  > common/de10nano: Cosmetic updates only
  > common/de10nano: Full HD 60 FPS support
  > adrv9009zu11eg:fmcomms8: Fix SPI timing constraint
  > ad_ip_jesd204_tpl_dac: Switch to sync arm toggling instead of setting only
  > up_dac_common: Move the sync status to register 0x1a to mirror adc path
  > ad_fmclidar1_ebz/a10soc: Fix a typo
  > Update system_top.v
  > ad9434_fmc,ad9467_fmc,fmcadc5: Update projects to use ad_iobuf, not IOBUF
  > intel: Update projects to use ad_iobuf instead of ALT_IOBUF
  > adrv9009zu11eg: Update spi module to use generic verilog
  > library: Move ad_iobuf to the common library, as it's not Xilinx specific
  > m2k: Add DAC last sample connections
  > axi_ad9963: Add last sample hold support
  > axi_dac_interpolate: Add last sample support
  > adv7513/de10nano: Define the USB clock
  > de10nano: Fix IO assignments
  > axi_ad7616: Update ad_edge_detect port names
  > ad469x: Remove sysid custom string init
  > ad469x_zed: Update bd.tcl with new port names
  > ad_edge_detect: Change port names
  > ad469x_fmc: Minor cosmetic update on the config file
  > fmcomms8: a10soc: Move RX and Observation to second SDRAM interface
  > common: a10soc: Allow for the second SDRAM interface to be used at a different clock
  > fmcomms8: a10soc: Initial commit
  > ad_ip_jesd204_tpl: Extend valid attribute ranges
  > ad469x: Add reference design for ad469x eval board
  > daq3: Update projects to the new TPL
  > adaq7980: Add AXI pulse generator to generate the offload trigger
  > Revert "axi_spi_engine: Add pulse_width and pulse_period registers"
  > makefile: Regenerate make files
  > util_sigma_delta_spi: Fix syntax
  > ad77681: Add axi_clkgen ip for spi engine
  > scripts/adi_pd_intel: Delete noisy print outs
  > adv7513/de10nano: Fix connection of ltc2308 SPI's interface
  > cn0540: Add axi_clkgen to Makefile
  > axi_ad6676: Set data format to twos complement
  > ad_ip_jesd204_tpl_adc: Fix PN check for twos complement data format
  > ad_ip_jesd204_tpl_dac_framer: fix localparam ordering
  > adrv9009_zu11eg: Add synchronization at application layer
  > ad9081_fmca_ebz: Fix device clocks termination
  > ad9656:Add reference design for the ad9656 eval board (#494)
  > sysid: Remove cstring init string
  > projects: cn0540: coraz7s: Add XADC support
  > cn0540/coraz7s: Set and input delay of one spi_clk cycle for the MISO line
  > cn0540/bd: Generate a 80MHz spi_clk
  > axi_gpreg: Add ttcl for clock_mon  constraints
  > sysid: Initialize parameter
  > sysid: Remove cstring init string
  > jesd204: Clean-up combinatorial logic
  > jesd204_rx: Reset frame alignment monitor event generator
  > axi_jesd204_rx: Ignore events if link not enabled
  > jesd204/jesd204_rx: Ignore frame alignment errors if lane is not in DATA phase
  > jesd204/jesd204_rx: Reset error counter once all lanes synced
  > jesd204_rx/jesd204_rx_ctrl: Fix de-glitch mechanism
  > axi_jesd204_common/jesd204_up_common: Add event stats
  > spi_engine: Add spi_engine.tcl
  > cn0363: Remove iobuf for spi sdo
  > cn0540/de10nano: Ignore 15003 critical warning
  > axi_hdmi_tx: Update register initialization
  > daq2/a10soc: Set optimization mode to high performance effort
  > common/s10soc: Input ports do not have a current strength property
  > adi_intel_msg: Dissable "unused TX/RX channel" critical warning for Stratix 10
  > ad77681evb: Remove redundant ad_data_clk
  > adrv9009: Fix typo for number of samples calculation for observation channel
  > fmcomms8: zcu102: Leave the SPI constraint at 25 MHz
  > fmcomms8: common: In the SPI module, use ad_iobuf instead of a Xilinx primitive
  > fmcomms8: zcu102: Remove the test pins, as they are not connected
  > library/commmon: Fix data width warnings
  > arradio: Remove unused signals
  > sysid: Fix board/project name underscore issue
  > cn0506_rmii: Fix no defined clock warnings
  > cn0540/de10nano: Delete GPIO connection to DRDY
  > cn0540/coraz7s: Time the SPI interface of AD7768-1
  > adv7513: Add initial project for de10nano
  > cn0540: Add de10nano reference design
  > de10: Delete redundant base design
  > common/de10nano: Add de10nano base design
  > adi_project_intel: Add de10nano support
  > spi_engine_offload: Define status_sync interface
  > spi_engine_offload: Delete trailing whitespaces
  > spi_engine_execution: Add missing parameter definition into hw.tcl script
  > axi_spi_engine: Fix the hw.tcl script
  > axi_spi_engine: Add missing ports to every sub-module instance
  > axi_spi_engine: Refactoring sdi_fifo read outs
  > axi_hdmi_tx_vdma: Use only synchronous reset
  > axi_hdmi_tx: Update IP to latest HDL flow
  > Add 'SE Base' family to the supported FPGAs
  > ad40xx_fmc/zed: Fix constraints, to avoid critical warnings in synthesis
  > spi_engine_offload: Start offload when DMA is ready
  > spi_engine_interconnect: always construct must not contains mixed assignment types
  > sysid_intel: Added sysid to intel projects
  > sysid_intel: Added adi_pd_intel.tcl
  > sysid_intel: Added hw.tcl for sysid IP cores
  > axi_ad9963: Fix warnings
  > axi_ad9467: Fix missing connection warnings
  > axi_ad9361: Fix missing connection warnings
  > axi_hdmi_tx: Fix warning on imageon
  > ad_csc: Fix warning for axi_hdmi_tx
  > common/ad_ss_422to444.v: Fix warning
  > m2k: Fix Warnings
  > axi_logic_analyzer: Fix data width warning
  > daq3:qsys: Activate input pipeline stage for AD9680's JESD interface
  > projects: adrv9009: intel: Update JESD204 LANE_RATE and REFCLK_FREQUENCY
  > s10soc: Insert an additional bridge between DMA and HPS
  > intel/axi_adxcvr: Use ad_ip_files process for source definition
  > adrv9009/qsys: input pipline active for jesd204_rx and jesd204_rx_os
  > intel/adi_jesd204: Add an additional pipeline stage to RX soft PCS
  > intel/adi_jesd204: Expose REGISTER_INPUTS parameter
  > jesd204_rx: Fix SDC constraint
  > adrv9009/s10soc: Add support for Stratix10 SOC
  > scripts/project_intel.mk: Update CLEAN targets
  > adrv9009/intel: Fix the register address layout
  > a10soc: Reconfiguration interface address width improvement
  > jesd204_framework: Add Stratix10 support
  > s10soc: Add new feature for ad_cpu_interconnect
  > stratix10soc: Initial commit of base design
  > axi_generic_adc: Declare parameters before use
  > adrv9001/zcu102: Loopback VADJ error to the FMC board
  > adrv9001/zed: Refactor VADJ test in VADJ error
  > adrv9001/zcu102: Update interface signal names based on direction
  > adrv9001/zed: Update interface signal names based on direction
  > library/common/ad_dds: Fix indentation
  > library/common/ad_dds: Fix initialization when 'valid' not constant
  > scripts/intel: Add message severity definition file
  > fmcomms2: a10soc remove project
  > axi_i2s_adi: create friendly xgui files
  > adrv9001/zed: Initial support for Zed
  > adrv9001:zcu102: Initial version
  > library:axi_adrv9001: Initial version
  > up_adc_common: Expose up version of r1_mode
  > library/common/up_dac_common: Sync dac_rst to control set
  > library/common/up_dac_common: Add registers to control interface
  > library/common/up_adc_common: Sync adc_rst to control set
  > library/common/up_adc_common: Add registers to control interface
  > ad_pnmon: Allow patterns with zero as valid data
  > ad_pngen: Generic PN generator
  > cn0540/coraz7s: Relax timing in SPI Engine
  > axi_spi_engine: Fix value range for ID parameter
  > spi_engine: Fix ip scripts for regmap, offload and execution
  > axi_spi_engine: Update IPXACT GUI layout
  > spi_engine_execution: Update IPXACT GUI layout
  > spi_engine_interconnect: Update IPXACT GUI layout
  > spi_engine_offload: Update IPXACT GUI layout
  > spi_engine: Add Intel Support
  > adi_project_intel: Update QSYS generation
  > daq2/a10gx: Set optimization mode to aggressive performance
  > adrv9371x/a10gx: Set optimization mode to aggressive performance
  > ad40xx_fmc: SDI delay should be set to 1
  > spi_engine_execution: code refactoring
  > spi_engine_execution: Fix sdi_shift_reg reset and command latching
  > ad_dds: Fix typo
  > axi_logic_analyzer: Optimize the input data path
  > axi_adc_trigger: Use valid in data delay stage
  > m2k: Update constraints
  > m2k: Connect signals for instrument sync
  > axi_adc_decimate: Export signals indicating the rate
  > axi_logic_analyzer: Auto sync to ADC path
  > axi_dmac: Add interface description register
  > scripts/intel: Update version check
  > scripts/intel: Set supported Quartus version to 19.3
  > util_cpack2: support for 64 channels
  > ad_ip_jesd204_tpl_adc: add support for 64 channels
  > ad_ip_jesd204_tpl_dac: expand address space to accomodate 64 channels
  > util_upack2: support for 64 channels
  > jesd204: DAC TPL to support 64 channels
  > fmcomms2/a10soc: Unused outputs should be left hanging
  > axi_ad9361: add_instance command must have a version attribute
  > adrv9009/a10gx: Delete redundant timing constraints
  > a10gx: Delete input/output delay definitions
  > daq3: Delete redundant timing constraint
  > daq2/a10gx: Use the default optimization mode
  > Revert "a10gx: Optimise the base design"
  > a10gx: Fix exceptionSlave interface definition for HPS
  > scripts/project-intel: Update CLEAN target
  > a10gx: Add a Avalon Pipeline Bridge between EMIF and DMA's
  > axi_laser_driver: Fix IP paramtere editor error
  > dac_fmc_ebz: QPRO is using apply_instance_preset
  > util_adcfifo: Update the interfaces for the asymetric memory
  > intel_mem_asym: Update the interface definitions
  > intel_mem_asym: add_instance command must have a version attribute
  > avl_dacfifo: add_intance command must have a version attribute
  > adi_jesd204: Delete redundant connections
  > adi_jesd204: add_instance command must have a version attribute
  > quartus: Increase tool version to 19.2
  > adi_project_intel: set_interconnect_requirment command is deprecated
  > ad9371:a10gx: Relax interconnect requirements
  > adrv9371:a10gx: Remove constraint from DDR
  > a10gx: Remove constraint from eth_ref_clk
  > adi_project_intel: Add support for Quartus Pro
  > adi_project_intel: Delete all MESSAGE_DISABLE assignment
  > quartus_pro: Global assignment ENABLE_ADVANCED_IO_TIMING is not supported
  > quartus_pro: Parameter property TYPE is not supported
  > Add cn0506_rmii/zcu102 support on revB
  > Add cn0506_rmii/zc706 support on revB
  > Add cn0506_rmii/zed support on revB
  > adi_intel_device_info_enc.tcl: Fix typo
  > ad_serdes_out: Add CMOS support
  > ad_serdes_in: Add CMOS support
  > ad_serdes_out: Add tristate option
  > up_delay_cntrl:ad_serdes_in: Make delay value width parametrizable
  > common/ad_serdes_out.v: Add US/US+ support
  > common/ad_serdes_in.v: Add US/US+ support
  > axi_dac_interpolate: oversampling optimization
  > axi_dac_interpolate: Fix oversampling by 2
  > ad_dds: Fix noise caused by dac_data_sync
  > jesd204_rx: Increment version to 1.04.a
  > jesd204_rx: Interrupt for unexpected lane status error
  > jesd204_rx: Generate interrupt on frame alignment error
  > axi_adxcvr: Reset status if PLL lock is lost
  > jesd204_rx: Don't auto reset on frame alignment error by default
  > jesd204_rx: Add RX frame alignment character check
  > m2k: Pattern Generator add instrument triggering
  > axi_logic_analyzer: Add trigger disable condition
  > axi_adc_trigger: Add trigger disable condition
  > jesd204: update README to reflect rev C
  > fmcomms5/zc702: Fix the sys_dma_clk connections
  > spi_engine_execution: Latch sdx_enabled
  > spi_engine_execution: Optimize SDI latch delay logic
  > daq2/xilinx: Update project to use generic JESD204 TPL
  > daq2/intel: Update project to use generic JESD204B TPL


Submodule buildroot 1daa690..a9818ab:
  > board/pluto/S45msd: Remove undesired character
  > update pluto and m2k on board html pages
  > configs/zynq_[pluto|m2k]_defconfig: Remove strace
  > package/libiio/libiio.mk: Update to git 2019_R2 (until next formal release)
  > board/pluto/device_format_jffs2: Fix fs cache issue
  > board: pluto: S23udc: Add option to select USB Ethernet Compatibility Mode
  > package: jesd204b_status: update to master HEAD
  > all-boards: update update motd configuration to new format
  > Merge tag '2020.02.8' from Buildroot upstream
  > configs/microblaze_adi_*_defconfig: Add package fru-tools
  > package: fru-tools: Add fru-tools utility
  > microblaze_*_defconfigs: update kernel headers to 4.19 for Vivado 2019.1
  > ci: split kernel version check for microblaze arch for Vivado 2019.1
  > Merge pull request #49 from analogdevicesinc/rgetz-update-m2k-html
  > board/m2k/S21misc: restore ssh authorized_keys from jffs2
  > configs: zynq_m2k_defconfig: Update for Vivado 2019.1 toolchain
  > Add quotes around the SSID and passphrase for the wifi to allow for spaces in them
  > board/m2k/post-build.sh: Add $ symbol
  > board: pluto & m2k: Temperature look-up table calib


Submodule u-boot-xlnx 469a0fd..a2c2013:
  > config: zynq-common: Remove compatible env setting
  > config: zynq-common: Fix attr_val attr_name
  > config: zynq-common: Fix refclk setting
  > configs: zynq-common: Use double quotes for strings
  > configs: zynq-common: Fix rev B fdt errors
  > configs: zynq-common: Fix mode 2r2t
  > configs: zynq-common: Guard against M2K platform
  > ci,pluto,m2k,azure-pipelines: add initial CI integration for Azure
  > configs: zynq-common: Fix SPI env update
  > configs: zynq-common: Fix 1r1t mode


Signed-off-by: Michael Hennerich <[email protected]>