1.41.0

[Koenkk]

Feel free to discuss the 1.41.0 release here!

[pannal]

I don't see any devices in the frontend after the upgrade. No errors in the logs. Downgrade back to 1.40.2 works well.

[pannal]

The frontend seems to fail with index-74e84a13.js:61 WebSocket connection to 'wss://xxxxxxx/zigbee/api' failed:

[pannal]

Issue found. This is due to the new base_url setting. Z2M is behind a reverse proxy and I had this config before:

    location ^~ /zigbee/api {
        proxy_pass         http://ip:port/api;
        proxy_set_header Host $host;

        proxy_http_version 1.1;
        proxy_set_header Upgrade $http_upgrade;
        proxy_set_header Connection "upgrade";
    }

    location ^~ /zigbee {
        include snippets/proxy.conf;
        proxy_pass http://ip:port/;
    }

Now we have to set base_url to /zigbee in this case and change the NGINX config to:

    location ^~ /zigbee/api {
        proxy_pass         http://ip:port;
        proxy_set_header Host $host;

        proxy_http_version 1.1;
        proxy_set_header Upgrade $http_upgrade;
        proxy_set_header Connection "upgrade";
    }

    location ^~ /zigbee {
        include snippets/proxy.conf;
        proxy_pass http://ip:port;
    }

[KirikauKiwi]

Not able to update the Ikea Inspiring smart plugs and existing problem with Aqara DJT11LM tilt sensor not showing readings since V1.4.0 or V1.4.1

[ClasheGit]

Hello, for my case, in 1.40.1-2 the axis of my aqara DJT11LM sensors no longer goes up. So I went back to 1.40.1-1, it worked again. Now, November 1st, update 1.41.0, all of my aqara sensors work perfectly. So I did the update from 1.40.1-1 directly to 1.41.0.

[pannal]

DJT11LM works 100% in 1.41.0 for me. All readings exist and update.

[KirikauKiwi]

Thanks, I took a further look at mine and it had disconnected from the Zigbee network, so all good 👍

[PlayFaster]

Hi. The new throttle option does not appear in the UI, but I can set it, and it works, in the YAML config. Is this (not in UI yet) expected behavior?

Also, is there any intent to introduce a throttle_ignore option, similar to debounce_ignore? I think this would be very useful, on for example mmWave presence/occupancy sensors, where I would like to throttle the output from the sensor, but always (throttle_ignore) immediately publish changes to the presence attribute itself.

[RangoDzh]

I found issue:

Device type
EndDevice
Zigbee Model
SNZB-03
Zigbee Manufacturer
eWeLink
Description
Motion sensor
Support status

Supported

IEEE Address
0xa4c138662d3deda1
Network address
0xEC92 / 60562
Firmware version
0122052017
Manufacturer
SONOFF
Model
SNZB-03

After today update, this device change type to water leak sensor, and stop working, after restore backup and repair, work normal with older version of package 1.40.2-1. Please solve.

[purche42]

Same problem with lights on/off which occurs first in 1.40.2
see lights problem #24293

[chris-1243]

Hi,

I randomly see polling issue on SNZB-02P/D since the update. I have 5 of them working fine and they were not throwing any errors at all since the last 2 updates (4 02P and 1 02D). It started on 1.40.2 quite randomly and only soms errors in the entire month of october.
1.41.1 is more or less one error every 24h and mainly the same sensor. The values are reported correctly just the errors in the logs like:

[2024-11-04 17:59:22] error: 	zh:controller:device: Handling of poll check-in from 0x0cae5ffffeb05d2e failed (ZCL command 0x0cae5ffffeb05d2e/1 genPollCtrl.checkinRsp({"startFastPolling":false,"fastPollTimeout":0}, {"timeout":10000,"disableResponse":false,"disableRecovery":false,"disableDefaultResponse":false,"direction":0,"reservedBits":0,"writeUndiv":false,"sendPolicy":"immediate"}) failed (Timeout - 59967 - 1 - 234 - 32 - 11 after 10000ms))

It is similar to #23166 but not the same devices. As a workaround, I might unbind the genPollCtrl cluster. No change in my setup as well...

[JJANOUSEK1]

Hi all, after update I have problem to display logs....I see only error

how to fix it? tks

[schwanenberg1969]

I have two instances running. Cannot delete either one.

Tried stopping both, deleting image --> error: still running

Reboot the whole snyology. Same problem.

Anybody with a solution?

[RobLeighton67]

I can set the throttle option via MQTT and see it in the configuration.yaml but even after restarting Z2M the messages still pour in every second from my Fluid level sensor. The setting appears to be overridden by my global device_options: debounce 0.5 setting.
I have removed the global device_options debounce and the throttle works as expected.
I'd prefer my global option to be overridden by the local setting (debounce or throttle)?

[drogago]

Hello. When is the next release expected?
I have a device that is currently unsupported. However, after reviewing the source code, I noticed that support appears to have been added. I’m considering whether it would make sense to implement temporary support on my own.

I apologize for posting this in this topic, but I felt it wasn't significant enough to warrant creating a new topic.

[Koenkk]

Every 1st of the month