UI improvements, Arabic translation, improvements tracing functionality, fix for blucon

• translation to Arabic
• fixes Spanish translations
• fix #98 Blucon ID input field/check inconsistent
• #104 trace file : no need to enable it in the settings, it is enabled by default. There's a maximum of 15 MB stored, which corresponds to around 6 days (depends on how much logs the specific installation is generating). The files are not deleted anymore but can be sent at any time.
• Yellow tint applied to all "+", "Scan" and "Connect" elements
• fix : send the MiaoMiao firmware and hardware to delegate

Finish translation + Bubble and MiaoMiao : manual sensor start allowed

3.10.2

version increase 3.10.2

Dexcom G6 firefly transmitter id's rejected. + fixes

enhancement #72. Dexcom transmitters with transmitter id 8G or 8H should be rejected
fix #73 When panning the chart back in time, and unit is mmol, then value is shown wrong
fix #74 Chart shows a gap after changing bloodglucose unit

MiaoMiao and Bubble users with OOP Web enabled will see full history after disconnect of more than 15 minutes

fix in 3.10.0 : MiaoMiao and Bubble users with OOP Web enabled will see full history after disconnect of more than 15 minutes. (# 71)

Fix #70 blucon : allow manual start

Blucon also supports automatic sensor start. However that doesn't always seem to work.
This fix allows manual start.

Fast drop and fast rise alert + upload sensor age to NS + fixes

New feature: Add fast drop and fast rise alerts (contribution by Oliver Searle-Barnes)

enhancement #53 upload sensor age to nightscout

fix #61 Wrong way to determine the Bubble hardware (not visible for user)
fix #62 XDrip is crashing after loosing the connection with Blucon
fix #63 crash when alert value given by user exceeds Int16 range
fix #64 crash when user gives invalid value in calibration textfield
fix #68 calculation of diff with previous value not correct if readings less than 5 minutes apart

create events in calendar when new readings, to support Apple Watch

Option to write latest glucose value in Calendar event. This allows to make reading visible in Apple Watch.

Following instructions are copied from Spike :
On your Apple Watch or the Watch app in your iOS device select the
"Modular" watch face and make sure you also select the "Calendar Complication" to be present in the middle of the watch face
Your glucose values should now start syncing to your watch when you receive your next reading from your CGM transmitter.
If by any chance you're not getting readings in your Apple Watch, go to the Watch app and under "General", "Reset"
click the "Reset Sync Data" and wait a few minutes.

watlaa + small fixes

• Watlaa connection, master mode (ie watlaa is master) - receives Libre packets and watlaa battery level

  This is a test version

  To setup Watlaa :

  • go to settings tab, select transmitter type Watlaa
  • go back to home screen
  • click transmitter
  • click start sensor and start the sensor
  • then go to the bluetooth tab (the second tab)
  • click the +
  • select watlaa
  • select watlaa master
  • scan
  • click 'done'

  xdrip should now receive the libre packets, you should get a calibration request

• Option to enable/disable nslog, see https://github.com/JohanDegraeve/xdripswift/wiki/NSLog

• fix #54, missed reading alerts goes on and on for ever

• fix #47, iPad crash when clicking transmitter button

Fix Dexcom G5 + minor fix

Fix #57 crash for Dexcom

Fix #56 wrong type of button when creating new alert entry

Nightscout and dexcom share upload schedule, ... other fixes and small improvements

• Option to specify when, during the day, upload to NightScout and Dexcom Share should happen
• M5Stack : option to switch off usage of WiFi
• fix #45 - setting value for battery, calibration, missed reading alerts was wrong when unit is mmol
• change in showing reading in badge counter : if notification on home screen is on, then use the notification to set the badge counter, so there's no need to multiply with 10 if value is mgdl