| TOP0 |
sdc/Heatpump_State |
Heatpump state (0=off, 1=on) |
| TOP1 |
sdc/Pump_Flow |
Pump flow (l/min) |
| TOP2 |
sdc/Force_DHW_State |
DHW status (0=off, 1=on) |
| TOP3 |
sdc/Quiet_Mode_Schedule |
Quiet mode schedule (0=inactive, 1=active) |
| TOP4 |
sdc/Operating_Mode_State |
Operating mode (0=Heat only, 1=Cool only, 2=Auto(Heat), 3=DHW only, 4=Heat+DHW, 5=Cool+DHW, 6=Auto(Heat)+DHW, 7=Auto(Cool), 8=Auto(Cool)+DHW) |
| TOP5 |
sdc/Main_Inlet_Temp |
Main inlet water temperature (°C) |
| TOP6 |
sdc/Main_Outlet_Temp |
Main outlet water temperature (°C) |
| TOP7 |
sdc/Main_Target_Temp |
Main outlet water target temperature (°C) |
| TOP8 |
sdc/Compressor_Freq |
Compressor frequency (Hz) |
| TOP9 |
sdc/DHW_Target_Temp |
DHW target temperature (°C) |
| TOP10 |
sdc/DHW_Temp |
Actual DHW temperature (°C) |
| TOP11 |
sdc/Operations_Hours |
Heatpump operating time (Hour) |
| TOP12 |
sdc/Operations_Counter |
Heatpump starts (counter) |
| TOP13 |
sdc/Main_Schedule_State |
Main thermostat schedule state (inactive - active) |
| TOP14 |
sdc/Outside_Temp |
Outside ambient temperature (°C) |
| TOP15 |
sdc/Heat_Energy_Production |
Thermal heat power production (Watt) |
| TOP16 |
sdc/Heat_Energy_Consumption |
Elektrical heat power consumption at heat mode (Watt) |
| TOP17 |
sdc/Powerful_Mode_Time |
Powerful state in minutes (0, 1, 2 or 3 x 30min) |
| TOP18 |
sdc/Quiet_Mode_Level |
Quiet mode level (0, 1, 2, 3) |
| TOP19 |
sdc/Holiday_Mode_State |
Holiday mode (0=off, 1=scheduled, 2=active) |
| TOP20 |
sdc/ThreeWay_Valve_State |
3-way valve mode (0=Room, 1=DHW) |
| TOP21 |
sdc/Outside_Pipe_Temp |
Outside pipe temperature (°C) |
| TOP22 |
sdc/DHW_Heat_Delta |
DHW heating delta (-12 to -2) (K) |
| TOP23 |
sdc/Heat_Delta |
Heat delta (K) |
| TOP24 |
sdc/Cool_Delta |
Cool delta (K) |
| TOP25 |
sdc/DHW_Holiday_Shift_Temp |
DHW Holiday shift temperature (-15 to +15) |
| TOP26 |
sdc/Defrosting_State |
Defrost state (0=off, 1=on) |
| TOP27 |
sdc/Z1_Heat_Request_Temp |
Zone 1 Heat Requested shift temp (-5 to 5) or direct heat temp (20 to max) |
| TOP28 |
sdc/Z1_Cool_Request_Temp |
Zone 1 Cool Requested shift temp (-5 to 5) or direct cool temp (5 to 20) |
| TOP29 |
sdc/Z1_Heat_Curve_Target_High_Temp |
Target temperature at lowest point on the heating curve (°C) |
| TOP30 |
sdc/Z1_Heat_Curve_Target_Low_Temp |
Target temperature at highest point on the heating curve (°C) |
| TOP31 |
sdc/Z1_Heat_Curve_Outside_High_Temp |
Lowest outside temperature on the heating curve (°C) |
| TOP32 |
sdc/Z1_Heat_Curve_Outside_Low_Temp |
Highest outside temperature on the heating curve (°C) |
| TOP33 |
sdc/Room_Thermostat_Temp |
Remote control thermostat temp (°C) |
| TOP34 |
sdc/Z2_Heat_Request_Temp |
Zone 2 Heat Requested shift temp (-5 to 5) or direct heat temp (20 to max) |
| TOP35 |
sdc/Z2_Cool_Request_Temp |
Zone 2 Cool Requested shift temp (-5 to 5) or direct cool temp (5 to 20) |
| TOP36 |
sdc/Z1_Water_Temp |
Zone 1 Water outlet temperature (°C) |
| TOP37 |
sdc/Z2_Water_Temp |
Zone 2 Water outlet temperature (°C) |
| TOP38 |
sdc/Cool_Energy_Production |
Thermal cooling power production (Watt) |
| TOP39 |
sdc/Cool_Energy_Consumption |
Elektrical cooling power consumption (Watt) |
| TOP40 |
sdc/DHW_Energy_Production |
Thermal DHW power production (Watt) |
| TOP41 |
sdc/DHW_Energy_Consumption |
Elektrical DHW power consumption (Watt) |
| TOP42 |
sdc/Z1_Water_Target_Temp |
Zone 1 water target temperature (°C) |
| TOP43 |
sdc/Z2_Water_Target_Temp |
Zone 2 water target temperature (°C) |
| TOP44 |
sdc/Error |
Last active Error from Heat Pump |
| TOP45 |
sdc/Room_Holiday_Shift_Temp |
Room heating Holiday shift temperature (-15 to 15) |
| TOP46 |
sdc/Buffer_Temp |
Actual Buffer temperature (°C) |
| TOP47 |
sdc/Solar_Temp |
Actual Solar temperature (°C) |
| TOP48 |
sdc/Pool_Temp |
Actual Pool temperature (°C) |
| TOP49 |
sdc/Main_Hex_Outlet_Temp |
Outlet 2, after heat exchanger water temperature (°C) |
| TOP50 |
sdc/Discharge_Temp |
Discharge Temperature (°C) |
| TOP51 |
sdc/Inside_Pipe_Temp |
Inside pipe temperature (°C) |
| TOP52 |
sdc/Defrost_Temp |
Defrost temperature (°C) |
| TOP53 |
sdc/Eva_Outlet_Temp |
Eva Outlet temperature (°C) |
| TOP54 |
sdc/Bypass_Outlet_Temp |
Bypass Outlet temperature (°C) |
| TOP55 |
sdc/Ipm_Temp |
Ipm temperature (°C) |
| TOP56 |
sdc/Z1_Temp |
Zone1: Actual Temperature (°C) |
| TOP57 |
sdc/Z2_Temp |
Zone2: Actual Temperature (°C) |
| TOP58 |
sdc/DHW_Heater_State |
When enabled, backup/booster heater can be used for DHW heating (disabled - enabled) |
| TOP59 |
sdc/Room_Heater_State |
When enabled, backup heater can be used for room heating (disabled - enabled) |
| TOP60 |
sdc/Internal_Heater_State |
Internal backup heater state (inactive - active) |
| TOP61 |
sdc/External_Heater_State |
External backup/booster heater state (inactive - active) |
| TOP62 |
sdc/Fan1_Motor_Speed |
Fan 1 Motor rotation speed (R/Min) |
| TOP63 |
sdc/Fan2_Motor_Speed |
Fan 2 Motor rotation speed (R/Min) |
| TOP64 |
sdc/High_Pressure |
High Pressure (Kgf/Cm2) |
| TOP65 |
sdc/Pump_Speed |
Pump Rotation Speed (R/Min) |
| TOP66 |
sdc/Low_Pressure |
Low Pressure (Kgf/Cm2) |
| TOP67 |
sdc/Compressor_Current |
Compressor/Outdoor unit Current (Ampere) |
| TOP68 |
sdc/Force_Heater_State |
Force heater status (0=inactive, 1=active) |
| TOP69 |
sdC/Sterilization_State |
Sterilisation State (0=inactive, 1=active) |
| TOP70 |
sdC/Sterilization_Temp |
Sterilisation Temperature (°C) |
| TOP71 |
sdC/Sterilization_Max_Time |
Sterilisation maximum time (minutes) |
| TOP72 |
sdc/Z1_Cool_Curve_Target_High_Temp |
Target temperature at lowest point on the cooling curve (°C) |
| TOP73 |
sdc/Z1_Cool_Curve_Target_Low_Temp |
Target temperature at highest point on the cooling curve (°C) |
| TOP74 |
sdc/Z1_Cool_Curve_Outside_High_Temp |
Lowest outside temperature on the cooling curve (°C) |
| TOP75 |
sdc/Z1_Cool_Curve_Outside_Low_Temp |
Highest outside temperature on the cooling curve (°C) |
| TOP76 |
sdc/Heating_Mode |
Compensation / Direct mode for heat (0 = compensation curve, 1 = direct) |
| TOP77 |
sdc/Heating_Off_Outdoor_Temp |
Above this outdoor temperature all heating is turned off(5 to 35 °C) |
| TOP78 |
sdc/Heater_On_Outdoor_Temp |
Below this temperature the backup heater is allowed to be used by heatpump heating logic(-15 to 20 °C) |
| TOP79 |
sdc/Heat_To_Cool_Temp |
Outdoor temperature to switch from heat to cool mode when in auto setting(°C) |
| TOP80 |
sdc/Cool_To_Heat_Temp |
Outdoor temperature to switch from cool to heat mode when in auto setting (°C) |
| TOP81 |
sdc/Cooling_Mode |
Compensation / Direct mode for cool (0 = compensation curve, 1 = direct) |
| TOP82 |
sdc/Z2_Heat_Curve_Target_High_Temp |
Target temperature at lowest point on the heating curve (°C) |
| TOP83 |
sdc/Z2_Heat_Curve_Target_Low_Temp |
Target temperature at highest point on the heating curve (°C) |
| TOP84 |
sdc/Z2_Heat_Curve_Outside_High_Temp |
Lowest outside temperature on the heating curve (°C) |
| TOP85 |
sdc/Z2_Heat_Curve_Outside_Low_Temp |
Highest outside temperature on the heating curve (°C) |
| TOP86 |
sdc/Z2_Cool_Curve_Target_High_Temp |
Target temperature at lowest point on the cooling curve (°C) |
| TOP87 |
sdc/Z2_Cool_Curve_Target_Low_Temp |
Target temperature at highest point on the cooling curve (°C) |
| TOP88 |
sdc/Z2_Cool_Curve_Outside_High_Temp |
Lowest outside temperature on the cooling curve (°C) |
| TOP89 |
sdc/Z2_Cool_Curve_Outside_Low_Temp |
Highest outside temperature on the cooling curve (°C) |
| TOP90 |
sdc/Room_Heater_Operations_Hours |
Electric heater operating time for Room (Hour) |
| TOP91 |
sdc/DHW_Heater_Operations_Hours |
Electric heater operating time for DHW (Hour) |
| TOP92 |
sdc/Heat_Pump_Model |
Heat pump model, all values in HeatPumpType.md |
| TOP93 |
sdc/Pump_Duty |
Pump duty |