Raise3D - E2.ini

# generated by PrusaSlicer 2.3.0+win64 on 2021-03-04 at 10:04:05 UTC

[print:0.10mm @E2 0.4]
avoid_crossing_perimeters = 0
avoid_crossing_perimeters_max_detour = 0
bottom_fill_pattern = monotonic
bottom_solid_layers = 7
bottom_solid_min_thickness = 0.5
bridge_acceleration = 0
bridge_angle = 0
bridge_flow_ratio = 1.4
bridge_speed = 15
brim_width = 0
clip_multipart_objects = 1
compatible_printers = 
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_RAISE3D.*/ and printer_notes=~/.*PRINTER_MODEL_E2.*/ and nozzle_diameter[0]==0.4
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
draft_shield = 0
elefant_foot_compensation = 0.2
ensure_vertical_shell_thickness = 1
external_perimeter_extrusion_width = 0.45
external_perimeter_speed = 72
external_perimeters_first = 0
extra_perimeters = 0
extruder_clearance_height = 27
extruder_clearance_radius = 52
extrusion_width = 0.45
fill_angle = 45
fill_density = 15%
fill_pattern = gyroid
first_layer_acceleration = 0
first_layer_extrusion_width = 0.42
first_layer_height = 0.2
first_layer_speed = 15
gap_fill_speed = 25
gcode_comments = 0
gcode_label_objects = 0
infill_acceleration = 0
infill_anchor = 2.5
infill_anchor_max = 12
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.45
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 0
infill_speed = 72
inherits = 
interface_shells = 0
ironing = 0
ironing_flowrate = 15%
ironing_spacing = 0.1
ironing_speed = 15
ironing_type = top
layer_height = 0.1
max_print_speed = 130
max_volumetric_speed = 0
min_skirt_length = 4
notes = 
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = {input_filename_base}_{nozzle_diameter[0]}n_{layer_height}mm_{filament_type[0]}_{printer_model}_{print_time}_{total_weight}g.gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0.45
perimeter_speed = 80
perimeters = 2
post_process = 
print_settings_id = 
raft_layers = 0
resolution = 0
seam_position = nearest
single_extruder_multi_material_priming = 0
skirt_distance = 2
skirt_height = 3
skirts = 1
slice_closing_radius = 0.049
small_perimeter_speed = 27
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.45
solid_infill_speed = 72
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_auto = 1
support_material_buildplate_only = 0
support_material_contact_distance = 0.15
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0.55
support_material_interface_contact_loops = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 2.5
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 45
support_material_synchronize_layers = 0
support_material_threshold = 55
support_material_with_sheath = 1
support_material_xy_spacing = 50%
thin_walls = 0
threads = 16
top_fill_pattern = monotonic
top_infill_extrusion_width = 0.4
top_solid_infill_speed = 72
top_solid_layers = 9
top_solid_min_thickness = 0.6
travel_speed = 150
wipe_tower = 0
wipe_tower_bridging = 10
wipe_tower_no_sparse_layers = 0
wipe_tower_rotation_angle = 0
wipe_tower_width = 60
wipe_tower_x = 180
wipe_tower_y = 140
xy_size_compensation = 0

[print:0.15mm @E2 0.4]
avoid_crossing_perimeters = 0
avoid_crossing_perimeters_max_detour = 0
bottom_fill_pattern = monotonic
bottom_solid_layers = 5
bottom_solid_min_thickness = 0.5
bridge_acceleration = 0
bridge_angle = 0
bridge_flow_ratio = 1.4
bridge_speed = 15
brim_width = 0
clip_multipart_objects = 1
compatible_printers = 
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_RAISE3D.*/ and printer_notes=~/.*PRINTER_MODEL_E2.*/ and nozzle_diameter[0]==0.4
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
draft_shield = 0
elefant_foot_compensation = 0.2
ensure_vertical_shell_thickness = 1
external_perimeter_extrusion_width = 0.45
external_perimeter_speed = 72
external_perimeters_first = 0
extra_perimeters = 0
extruder_clearance_height = 27
extruder_clearance_radius = 52
extrusion_width = 0.45
fill_angle = 45
fill_density = 15%
fill_pattern = gyroid
first_layer_acceleration = 0
first_layer_extrusion_width = 0.42
first_layer_height = 0.2
first_layer_speed = 15
gap_fill_speed = 25
gcode_comments = 0
gcode_label_objects = 0
infill_acceleration = 0
infill_anchor = 2.5
infill_anchor_max = 12
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.45
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 0
infill_speed = 72
inherits = 
interface_shells = 0
ironing = 0
ironing_flowrate = 15%
ironing_spacing = 0.1
ironing_speed = 15
ironing_type = top
layer_height = 0.15
max_print_speed = 130
max_volumetric_speed = 0
min_skirt_length = 4
notes = 
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = {input_filename_base}_{nozzle_diameter[0]}n_{layer_height}mm_{filament_type[0]}_{printer_model}_{print_time}_{total_weight}g.gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0.45
perimeter_speed = 80
perimeters = 2
post_process = 
print_settings_id = 
raft_layers = 0
resolution = 0
seam_position = nearest
single_extruder_multi_material_priming = 0
skirt_distance = 2
skirt_height = 3
skirts = 1
slice_closing_radius = 0.049
small_perimeter_speed = 27
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.45
solid_infill_speed = 72
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_auto = 1
support_material_buildplate_only = 0
support_material_contact_distance = 0.15
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0.55
support_material_interface_contact_loops = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 2.5
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 45
support_material_synchronize_layers = 0
support_material_threshold = 55
support_material_with_sheath = 1
support_material_xy_spacing = 50%
thin_walls = 0
threads = 16
top_fill_pattern = monotonic
top_infill_extrusion_width = 0.4
top_solid_infill_speed = 72
top_solid_layers = 7
top_solid_min_thickness = 0.6
travel_speed = 150
wipe_tower = 0
wipe_tower_bridging = 10
wipe_tower_no_sparse_layers = 0
wipe_tower_rotation_angle = 0
wipe_tower_width = 60
wipe_tower_x = 180
wipe_tower_y = 140
xy_size_compensation = 0

[print:0.15mm @E2 0.6]
avoid_crossing_perimeters = 0
avoid_crossing_perimeters_max_detour = 0
bottom_fill_pattern = monotonic
bottom_solid_layers = 5
bottom_solid_min_thickness = 0.5
bridge_acceleration = 0
bridge_angle = 0
bridge_flow_ratio = 1.4
bridge_speed = 25
brim_width = 0
clip_multipart_objects = 1
compatible_printers = 
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_RAISE3D.*/ and printer_notes=~/.*PRINTER_MODEL_E2.*/ and nozzle_diameter[0]==0.6
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
draft_shield = 0
elefant_foot_compensation = 0.2
ensure_vertical_shell_thickness = 0
external_perimeter_extrusion_width = 0.68
external_perimeter_speed = 35
external_perimeters_first = 1
extra_perimeters = 0
extruder_clearance_height = 27
extruder_clearance_radius = 52
extrusion_width = 0.65
fill_angle = 45
fill_density = 15%
fill_pattern = gyroid
first_layer_acceleration = 0
first_layer_extrusion_width = 0.65
first_layer_height = 0.3
first_layer_speed = 15
gap_fill_speed = 50
gcode_comments = 0
gcode_label_objects = 0
infill_acceleration = 0
infill_anchor = 2.5
infill_anchor_max = 15
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.68
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 0%
infill_speed = 70
inherits = 
interface_shells = 0
ironing = 0
ironing_flowrate = 15%
ironing_spacing = 0.15
ironing_speed = 15
ironing_type = top
layer_height = 0.15
max_print_speed = 90
max_volumetric_speed = 0
min_skirt_length = 4
notes = 
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = {input_filename_base}_{nozzle_diameter[0]}n_{layer_height}mm_{filament_type[0]}_{printer_model}_{print_time}_{total_weight}g.gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0.68
perimeter_speed = 45
perimeters = 2
post_process = 
print_settings_id = 
raft_layers = 0
resolution = 0
seam_position = aligned
single_extruder_multi_material_priming = 0
skirt_distance = 2
skirt_height = 3
skirts = 1
slice_closing_radius = 0.049
small_perimeter_speed = 25
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.68
solid_infill_speed = 60
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_auto = 1
support_material_buildplate_only = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0.55
support_material_interface_contact_loops = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 5
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 45
support_material_synchronize_layers = 0
support_material_threshold = 45
support_material_with_sheath = 1
support_material_xy_spacing = 50%
thin_walls = 0
threads = 16
top_fill_pattern = monotonic
top_infill_extrusion_width = 0.6
top_solid_infill_speed = 60
top_solid_layers = 7
top_solid_min_thickness = 0.6
travel_speed = 150
wipe_tower = 0
wipe_tower_bridging = 10
wipe_tower_no_sparse_layers = 0
wipe_tower_rotation_angle = 0
wipe_tower_width = 60
wipe_tower_x = 180
wipe_tower_y = 140
xy_size_compensation = 0

[print:0.20mm @E2 0.4]
avoid_crossing_perimeters = 0
avoid_crossing_perimeters_max_detour = 0
bottom_fill_pattern = monotonic
bottom_solid_layers = 4
bottom_solid_min_thickness = 0.5
bridge_acceleration = 0
bridge_angle = 0
bridge_flow_ratio = 1.4
bridge_speed = 15
brim_width = 0
clip_multipart_objects = 1
compatible_printers = 
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_RAISE3D.*/ and printer_notes=~/.*PRINTER_MODEL_E2.*/ and nozzle_diameter[0]==0.4
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
draft_shield = 0
elefant_foot_compensation = 0.2
ensure_vertical_shell_thickness = 1
external_perimeter_extrusion_width = 0.45
external_perimeter_speed = 72
external_perimeters_first = 1
extra_perimeters = 0
extruder_clearance_height = 27
extruder_clearance_radius = 52
extrusion_width = 0.45
fill_angle = 45
fill_density = 15%
fill_pattern = gyroid
first_layer_acceleration = 0
first_layer_extrusion_width = 0.42
first_layer_height = 0.2
first_layer_speed = 15
gap_fill_speed = 25
gcode_comments = 0
gcode_label_objects = 0
infill_acceleration = 0
infill_anchor = 2.5
infill_anchor_max = 12
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.45
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 0
infill_speed = 72
inherits = 
interface_shells = 0
ironing = 0
ironing_flowrate = 15%
ironing_spacing = 0.1
ironing_speed = 15
ironing_type = top
layer_height = 0.2
max_print_speed = 130
max_volumetric_speed = 0
min_skirt_length = 4
notes = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = {input_filename_base}_{nozzle_diameter[0]}n_{layer_height}mm_{filament_type[0]}_{printer_model}_{print_time}_{total_weight}g.gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0.45
perimeter_speed = 80
perimeters = 2
post_process = 
print_settings_id = 
raft_layers = 0
resolution = 0
seam_position = aligned
single_extruder_multi_material_priming = 0
skirt_distance = 2
skirt_height = 3
skirts = 1
slice_closing_radius = 0.049
small_perimeter_speed = 27
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.45
solid_infill_speed = 72
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_auto = 1
support_material_buildplate_only = 0
support_material_contact_distance = 0.15
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0.55
support_material_interface_contact_loops = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 2.5
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 45
support_material_synchronize_layers = 0
support_material_threshold = 55
support_material_with_sheath = 1
support_material_xy_spacing = 50%
thin_walls = 0
threads = 16
top_fill_pattern = monotonic
top_infill_extrusion_width = 0.4
top_solid_infill_speed = 72
top_solid_layers = 5
top_solid_min_thickness = 0.6
travel_speed = 150
wipe_tower = 0
wipe_tower_bridging = 10
wipe_tower_no_sparse_layers = 0
wipe_tower_rotation_angle = 0
wipe_tower_width = 60
wipe_tower_x = 180
wipe_tower_y = 140
xy_size_compensation = 0

[print:0.20mm @E2 0.6]
avoid_crossing_perimeters = 0
avoid_crossing_perimeters_max_detour = 0
bottom_fill_pattern = monotonic
bottom_solid_layers = 4
bottom_solid_min_thickness = 0.5
bridge_acceleration = 0
bridge_angle = 0
bridge_flow_ratio = 1.4
bridge_speed = 15
brim_width = 0
clip_multipart_objects = 1
compatible_printers = 
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_RAISE3D.*/ and printer_notes=~/.*PRINTER_MODEL_E2.*/ and nozzle_diameter[0]==0.6
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
draft_shield = 0
elefant_foot_compensation = 0.2
ensure_vertical_shell_thickness = 0
external_perimeter_extrusion_width = 0.68
external_perimeter_speed = 35
external_perimeters_first = 1
extra_perimeters = 0
extruder_clearance_height = 27
extruder_clearance_radius = 52
extrusion_width = 0.65
fill_angle = 45
fill_density = 15%
fill_pattern = gyroid
first_layer_acceleration = 0
first_layer_extrusion_width = 0.65
first_layer_height = 0.3
first_layer_speed = 15
gap_fill_speed = 50
gcode_comments = 0
gcode_label_objects = 0
infill_acceleration = 0
infill_anchor = 2.5
infill_anchor_max = 12
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.68
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 0%
infill_speed = 70
inherits = 
interface_shells = 0
ironing = 0
ironing_flowrate = 15%
ironing_spacing = 0.15
ironing_speed = 15
ironing_type = top
layer_height = 0.2
max_print_speed = 90
max_volumetric_speed = 0
min_skirt_length = 4
notes = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = {input_filename_base}_{nozzle_diameter[0]}n_{layer_height}mm_{filament_type[0]}_{printer_model}_{print_time}_{total_weight}g.gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0.68
perimeter_speed = 45
perimeters = 2
post_process = 
print_settings_id = 
raft_layers = 0
resolution = 0
seam_position = aligned
single_extruder_multi_material_priming = 0
skirt_distance = 2
skirt_height = 3
skirts = 1
slice_closing_radius = 0.049
small_perimeter_speed = 25
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.68
solid_infill_speed = 70
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_auto = 1
support_material_buildplate_only = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0.55
support_material_interface_contact_loops = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 5
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 50
support_material_synchronize_layers = 0
support_material_threshold = 45
support_material_with_sheath = 1
support_material_xy_spacing = 50%
thin_walls = 0
threads = 16
top_fill_pattern = monotonic
top_infill_extrusion_width = 0.6
top_solid_infill_speed = 60
top_solid_layers = 5
top_solid_min_thickness = 0.6
travel_speed = 150
wipe_tower = 0
wipe_tower_bridging = 10
wipe_tower_no_sparse_layers = 0
wipe_tower_rotation_angle = 0
wipe_tower_width = 60
wipe_tower_x = 180
wipe_tower_y = 140
xy_size_compensation = 0

[print:0.30mm @E2 0.4]
avoid_crossing_perimeters = 0
avoid_crossing_perimeters_max_detour = 0
bottom_fill_pattern = monotonic
bottom_solid_layers = 3
bottom_solid_min_thickness = 0.5
bridge_acceleration = 0
bridge_angle = 0
bridge_flow_ratio = 1.4
bridge_speed = 15
brim_width = 0
clip_multipart_objects = 1
compatible_printers = 
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_RAISE3D.*/ and printer_notes=~/.*PRINTER_MODEL_E2.*/ and nozzle_diameter[0]==0.4
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
draft_shield = 0
elefant_foot_compensation = 0.2
ensure_vertical_shell_thickness = 1
external_perimeter_extrusion_width = 0.6
external_perimeter_speed = 72
external_perimeters_first = 0
extra_perimeters = 0
extruder_clearance_height = 27
extruder_clearance_radius = 52
extrusion_width = 0.5
fill_angle = 45
fill_density = 15%
fill_pattern = gyroid
first_layer_acceleration = 0
first_layer_extrusion_width = 0.42
first_layer_height = 0.2
first_layer_speed = 15
gap_fill_speed = 25
gcode_comments = 0
gcode_label_objects = 0
infill_acceleration = 0
infill_anchor = 2.5
infill_anchor_max = 12
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.5
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 0
infill_speed = 72
inherits = 
interface_shells = 0
ironing = 0
ironing_flowrate = 15%
ironing_spacing = 0.1
ironing_speed = 15
ironing_type = top
layer_height = 0.3
max_print_speed = 130
max_volumetric_speed = 0
min_skirt_length = 4
notes = 
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = {input_filename_base}_{nozzle_diameter[0]}n_{layer_height}mm_{filament_type[0]}_{printer_model}_{print_time}_{total_weight}g.gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0.5
perimeter_speed = 80
perimeters = 2
post_process = 
print_settings_id = 
raft_layers = 0
resolution = 0
seam_position = nearest
single_extruder_multi_material_priming = 0
skirt_distance = 2
skirt_height = 3
skirts = 1
slice_closing_radius = 0.049
small_perimeter_speed = 27
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.5
solid_infill_speed = 72
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_auto = 1
support_material_buildplate_only = 0
support_material_contact_distance = 0.15
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0.55
support_material_interface_contact_loops = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 2.5
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 45
support_material_synchronize_layers = 0
support_material_threshold = 55
support_material_with_sheath = 1
support_material_xy_spacing = 50%
thin_walls = 0
threads = 16
top_fill_pattern = monotonic
top_infill_extrusion_width = 0.45
top_solid_infill_speed = 72
top_solid_layers = 4
top_solid_min_thickness = 0.6
travel_speed = 150
wipe_tower = 0
wipe_tower_bridging = 10
wipe_tower_no_sparse_layers = 0
wipe_tower_rotation_angle = 0
wipe_tower_width = 60
wipe_tower_x = 180
wipe_tower_y = 140
xy_size_compensation = 0

[print:0.30mm @E2 0.6]
avoid_crossing_perimeters = 0
avoid_crossing_perimeters_max_detour = 0
bottom_fill_pattern = monotonic
bottom_solid_layers = 4
bottom_solid_min_thickness = 0.5
bridge_acceleration = 0
bridge_angle = 0
bridge_flow_ratio = 1.4
bridge_speed = 15
brim_width = 0
clip_multipart_objects = 1
compatible_printers = 
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_RAISE3D.*/ and printer_notes=~/.*PRINTER_MODEL_E2.*/ and nozzle_diameter[0]==0.6
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
draft_shield = 0
elefant_foot_compensation = 0.2
ensure_vertical_shell_thickness = 0
external_perimeter_extrusion_width = 0.68
external_perimeter_speed = 72
external_perimeters_first = 1
extra_perimeters = 0
extruder_clearance_height = 27
extruder_clearance_radius = 52
extrusion_width = 0.65
fill_angle = 45
fill_density = 15%
fill_pattern = gyroid
first_layer_acceleration = 0
first_layer_extrusion_width = 0.65
first_layer_height = 0.3
first_layer_speed = 15
gap_fill_speed = 25
gcode_comments = 0
gcode_label_objects = 0
infill_acceleration = 0
infill_anchor = 2.5
infill_anchor_max = 12
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.68
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 0
infill_speed = 72
inherits = 
interface_shells = 0
ironing = 0
ironing_flowrate = 15%
ironing_spacing = 0.15
ironing_speed = 15
ironing_type = top
layer_height = 0.3
max_print_speed = 130
max_volumetric_speed = 0
min_skirt_length = 4
notes = 
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = {input_filename_base}_{nozzle_diameter[0]}n_{layer_height}mm_{filament_type[0]}_{printer_model}_{print_time}_{total_weight}g.gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0.68
perimeter_speed = 80
perimeters = 4
post_process = 
print_settings_id = 
raft_layers = 0
resolution = 0
seam_position = aligned
single_extruder_multi_material_priming = 0
skirt_distance = 2
skirt_height = 3
skirts = 1
slice_closing_radius = 0.049
small_perimeter_speed = 27
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.68
solid_infill_speed = 72
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_auto = 1
support_material_buildplate_only = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0.55
support_material_interface_contact_loops = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 5
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 45
support_material_synchronize_layers = 0
support_material_threshold = 45
support_material_with_sheath = 1
support_material_xy_spacing = 50%
thin_walls = 0
threads = 16
top_fill_pattern = monotonic
top_infill_extrusion_width = 0.6
top_solid_infill_speed = 72
top_solid_layers = 4
top_solid_min_thickness = 0.6
travel_speed = 150
wipe_tower = 0
wipe_tower_bridging = 10
wipe_tower_no_sparse_layers = 0
wipe_tower_rotation_angle = 0
wipe_tower_width = 60
wipe_tower_x = 180
wipe_tower_y = 140
xy_size_compensation = 0

[print:0.35mm @E2 0.6]
avoid_crossing_perimeters = 0
avoid_crossing_perimeters_max_detour = 0
bottom_fill_pattern = monotonic
bottom_solid_layers = 3
bottom_solid_min_thickness = 0.5
bridge_acceleration = 0
bridge_angle = 0
bridge_flow_ratio = 1.4
bridge_speed = 15
brim_width = 0
clip_multipart_objects = 1
compatible_printers = 
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_RAISE3D.*/ and printer_notes=~/.*PRINTER_MODEL_E2.*/ and nozzle_diameter[0]==0.6
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
draft_shield = 0
elefant_foot_compensation = 0.2
ensure_vertical_shell_thickness = 0
external_perimeter_extrusion_width = 0.68
external_perimeter_speed = 35
external_perimeters_first = 1
extra_perimeters = 0
extruder_clearance_height = 27
extruder_clearance_radius = 52
extrusion_width = 0.65
fill_angle = 45
fill_density = 15%
fill_pattern = gyroid
first_layer_acceleration = 0
first_layer_extrusion_width = 0.65
first_layer_height = 0.3
first_layer_speed = 15
gap_fill_speed = 25
gcode_comments = 0
gcode_label_objects = 0
infill_acceleration = 0
infill_anchor = 2.5
infill_anchor_max = 15
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.68
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 0%
infill_speed = 70
inherits = 
interface_shells = 0
ironing = 0
ironing_flowrate = 15%
ironing_spacing = 0.15
ironing_speed = 15
ironing_type = top
layer_height = 0.35
max_print_speed = 90
max_volumetric_speed = 0
min_skirt_length = 4
notes = 
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = {input_filename_base}_{nozzle_diameter[0]}n_{layer_height}mm_{filament_type[0]}_{printer_model}_{print_time}_{total_weight}g.gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0.68
perimeter_speed = 45
perimeters = 2
post_process = 
print_settings_id = 
raft_layers = 0
resolution = 0
seam_position = aligned
single_extruder_multi_material_priming = 0
skirt_distance = 2
skirt_height = 3
skirts = 1
slice_closing_radius = 0.049
small_perimeter_speed = 25
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.68
solid_infill_speed = 70
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_auto = 1
support_material_buildplate_only = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0.55
support_material_interface_contact_loops = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 5
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 50
support_material_synchronize_layers = 0
support_material_threshold = 45
support_material_with_sheath = 0
support_material_xy_spacing = 50%
thin_walls = 0
threads = 16
top_fill_pattern = monotonic
top_infill_extrusion_width = 0.6
top_solid_infill_speed = 60
top_solid_layers = 4
top_solid_min_thickness = 0.6
travel_speed = 150
wipe_tower = 0
wipe_tower_bridging = 10
wipe_tower_no_sparse_layers = 0
wipe_tower_rotation_angle = 0
wipe_tower_width = 60
wipe_tower_x = 180
wipe_tower_y = 140
xy_size_compensation = 0

[print:0.40mm @E2 0.6]
avoid_crossing_perimeters = 0
avoid_crossing_perimeters_max_detour = 0
bottom_fill_pattern = monotonic
bottom_solid_layers = 3
bottom_solid_min_thickness = 0.5
bridge_acceleration = 0
bridge_angle = 0
bridge_flow_ratio = 1.4
bridge_speed = 15
brim_width = 0
clip_multipart_objects = 1
compatible_printers = 
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_RAISE3D.*/ and printer_notes=~/.*PRINTER_MODEL_E2.*/ and nozzle_diameter[0]==0.6
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
draft_shield = 0
elefant_foot_compensation = 0.2
ensure_vertical_shell_thickness = 0
external_perimeter_extrusion_width = 0.68
external_perimeter_speed = 35
external_perimeters_first = 1
extra_perimeters = 0
extruder_clearance_height = 27
extruder_clearance_radius = 52
extrusion_width = 0.65
fill_angle = 45
fill_density = 15%
fill_pattern = gyroid
first_layer_acceleration = 0
first_layer_extrusion_width = 0.65
first_layer_height = 0.3
first_layer_speed = 15
gap_fill_speed = 25
gcode_comments = 0
gcode_label_objects = 0
infill_acceleration = 0
infill_anchor = 2.5
infill_anchor_max = 15
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.68
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 0%
infill_speed = 70
inherits = 
interface_shells = 0
ironing = 0
ironing_flowrate = 15%
ironing_spacing = 0.15
ironing_speed = 15
ironing_type = top
layer_height = 0.4
max_print_speed = 90
max_volumetric_speed = 0
min_skirt_length = 4
notes = 
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = {input_filename_base}_{nozzle_diameter[0]}n_{layer_height}mm_{filament_type[0]}_{printer_model}_{print_time}_{total_weight}g.gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0.68
perimeter_speed = 45
perimeters = 2
post_process = 
print_settings_id = 
raft_layers = 0
resolution = 0
seam_position = aligned
single_extruder_multi_material_priming = 0
skirt_distance = 2
skirt_height = 3
skirts = 1
slice_closing_radius = 0.049
small_perimeter_speed = 25
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.68
solid_infill_speed = 70
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_auto = 1
support_material_buildplate_only = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0.55
support_material_interface_contact_loops = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 5
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 50
support_material_synchronize_layers = 0
support_material_threshold = 45
support_material_with_sheath = 1
support_material_xy_spacing = 50%
thin_walls = 0
threads = 16
top_fill_pattern = monotonic
top_infill_extrusion_width = 0.6
top_solid_infill_speed = 60
top_solid_layers = 4
top_solid_min_thickness = 0.6
travel_speed = 150
wipe_tower = 0
wipe_tower_bridging = 10
wipe_tower_no_sparse_layers = 0
wipe_tower_rotation_angle = 0
wipe_tower_width = 60
wipe_tower_x = 180
wipe_tower_y = 140
xy_size_compensation = 0

[filament:ABS @E2]
bed_temperature = 100
bridge_fan_speed = 25
compatible_printers = 
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_RAISE3D.*/ and printer_notes=~/.*PRINTER_MODEL_E2.*/ and nozzle_diameter[0]==0.4
compatible_prints = 
compatible_prints_condition = 
cooling = 1
disable_fan_first_layers = 4
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 30
filament_colour = #FF8000
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 30
filament_density = 1.12
filament_deretract_speed = nil
filament_diameter = 1.75
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 11
filament_minimal_purge_on_wipe_tower = 15
filament_notes = ""
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_lift = 0.2
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_speed = nil
filament_settings_id = ""
filament_soluble = 0
filament_spool_weight = 0
filament_toolchange_delay = 0
filament_type = ABS
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_vendor = (Unknown)
filament_wipe = nil
first_layer_bed_temperature = 100
first_layer_temperature = 250
full_fan_speed_layer = 0
inherits = 
max_fan_speed = 15
min_fan_speed = 15
min_print_speed = 15
slowdown_below_layer_time = 20
start_filament_gcode = "; Filament gcode\nM572 D0 S0.07\nM572 D1 S0.07"
temperature = 250

[filament:ABS @E2 0.6n]
bed_temperature = 100
bridge_fan_speed = 25
compatible_printers = 
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_RAISE3D.*/ and printer_notes=~/.*PRINTER_MODEL_E2.*/ and nozzle_diameter[0]==0.6
compatible_prints = 
compatible_prints_condition = 
cooling = 1
disable_fan_first_layers = 4
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
extrusion_multiplier = 1.1
fan_always_on = 0
fan_below_layer_time = 30
filament_colour = #FF8000
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 30
filament_density = 1.12
filament_deretract_speed = nil
filament_diameter = 1.75
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 11
filament_minimal_purge_on_wipe_tower = 15
filament_notes = ""
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_lift = 0.2
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_speed = nil
filament_settings_id = ""
filament_soluble = 0
filament_spool_weight = 0
filament_toolchange_delay = 0
filament_type = ABS
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_vendor = (Unknown)
filament_wipe = nil
first_layer_bed_temperature = 100
first_layer_temperature = 250
full_fan_speed_layer = 0
inherits = 
max_fan_speed = 15
min_fan_speed = 15
min_print_speed = 15
slowdown_below_layer_time = 20
start_filament_gcode = "; Filament gcode\nM572 D0 S0.07\nM572 D1 S0.07"
temperature = 250

[filament:FLEX @E2]
bed_temperature = 60
bridge_fan_speed = 80
compatible_printers = 
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_RAISE3D.*/ and printer_notes=~/.*PRINTER_MODEL_E2.*/ and nozzle_diameter[0]==0.4
compatible_prints = 
compatible_prints_condition = 
cooling = 0
disable_fan_first_layers = 1
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 100
filament_colour = #008000
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 30
filament_density = 1.22
filament_deretract_speed = nil
filament_diameter = 1.75
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 1.2
filament_minimal_purge_on_wipe_tower = 15
filament_notes = ""
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = 0
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_speed = nil
filament_settings_id = ""
filament_soluble = 0
filament_spool_weight = 0
filament_toolchange_delay = 0
filament_type = FLEX
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_vendor = (Unknown)
filament_wipe = nil
first_layer_bed_temperature = 60
first_layer_temperature = 240
full_fan_speed_layer = 4
inherits = 
max_fan_speed = 100
min_fan_speed = 100
min_print_speed = 15
slowdown_below_layer_time = 15
start_filament_gcode = "; Filament gcode\n"
temperature = 240

[filament:FLEX @E2 0.6n]
bed_temperature = 60
bridge_fan_speed = 80
compatible_printers = 
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_RAISE3D.*/ and printer_notes=~/.*PRINTER_MODEL_E2.*/ and nozzle_diameter[0]==0.6
compatible_prints = 
compatible_prints_condition = 
cooling = 0
disable_fan_first_layers = 1
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
extrusion_multiplier = 1.1
fan_always_on = 0
fan_below_layer_time = 100
filament_colour = #008000
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 30
filament_density = 1.22
filament_deretract_speed = nil
filament_diameter = 1.75
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 1.2
filament_minimal_purge_on_wipe_tower = 15
filament_notes = ""
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = 0
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_speed = nil
filament_settings_id = ""
filament_soluble = 0
filament_spool_weight = 0
filament_toolchange_delay = 0
filament_type = FLEX
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_vendor = (Unknown)
filament_wipe = nil
first_layer_bed_temperature = 60
first_layer_temperature = 240
full_fan_speed_layer = 4
inherits = 
max_fan_speed = 100
min_fan_speed = 100
min_print_speed = 15
slowdown_below_layer_time = 15
start_filament_gcode = "; Filament gcode\n"
temperature = 240

[filament:PETG @E2]
bed_temperature = 70
bridge_fan_speed = 50
compatible_printers = 
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_RAISE3D.*/ and printer_notes=~/.*PRINTER_MODEL_E2.*/ and nozzle_diameter[0]==0.4
compatible_prints = 
compatible_prints_condition = 
cooling = 1
disable_fan_first_layers = 3
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 20
filament_colour = #FF8000
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 50
filament_density = 1.27
filament_deretract_speed = nil
filament_diameter = 1.75
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 8
filament_minimal_purge_on_wipe_tower = 15
filament_notes = ""
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_lift = 0.2
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_speed = nil
filament_settings_id = ""
filament_soluble = 0
filament_spool_weight = 0
filament_toolchange_delay = 0
filament_type = PET
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_vendor = (Unknown)
filament_wipe = nil
first_layer_bed_temperature = 70
first_layer_temperature = 245
full_fan_speed_layer = 0
inherits = 
max_fan_speed = 50
min_fan_speed = 30
min_print_speed = 15
slowdown_below_layer_time = 15
start_filament_gcode = "; Filament gcode\nM572 D0 S0.14\nM572 D1 S0.14"
temperature = 245

[filament:PETG @E2 0.6n]
bed_temperature = 70
bridge_fan_speed = 50
compatible_printers = 
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_RAISE3D.*/ and printer_notes=~/.*PRINTER_MODEL_E2.*/ and nozzle_diameter[0]==0.6
compatible_prints = 
compatible_prints_condition = 
cooling = 1
disable_fan_first_layers = 3
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
extrusion_multiplier = 1.1
fan_always_on = 1
fan_below_layer_time = 20
filament_colour = #FF8000
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 50
filament_density = 1.27
filament_deretract_speed = nil
filament_diameter = 1.75
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 8
filament_minimal_purge_on_wipe_tower = 15
filament_notes = ""
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_lift = 0.2
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_speed = nil
filament_settings_id = ""
filament_soluble = 0
filament_spool_weight = 0
filament_toolchange_delay = 0
filament_type = PET
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_vendor = (Unknown)
filament_wipe = nil
first_layer_bed_temperature = 70
first_layer_temperature = 245
full_fan_speed_layer = 0
inherits = 
max_fan_speed = 50
min_fan_speed = 30
min_print_speed = 15
slowdown_below_layer_time = 15
start_filament_gcode = "; Filament gcode\nM572 D0 S0.14\nM572 D1 S0.14"
temperature = 245

[filament:PLA @E2]
bed_temperature = 60
bridge_fan_speed = 100
compatible_printers = 
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_RAISE3D.*/ and printer_notes=~/.*PRINTER_MODEL_E2.*/ and nozzle_diameter[0]==0.4
compatible_prints = 
compatible_prints_condition = 
cooling = 1
disable_fan_first_layers = 1
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
extrusion_multiplier = 1.1
fan_always_on = 1
fan_below_layer_time = 60
filament_colour = #FF8000
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 30
filament_density = 1.24
filament_deretract_speed = nil
filament_diameter = 1.75
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 15
filament_minimal_purge_on_wipe_tower = 15
filament_notes = ""
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_speed = nil
filament_settings_id = ""
filament_soluble = 0
filament_spool_weight = 0
filament_toolchange_delay = 0
filament_type = PLA
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_vendor = (Unknown)
filament_wipe = nil
first_layer_bed_temperature = 60
first_layer_temperature = 220
full_fan_speed_layer = 0
inherits = 
max_fan_speed = 100
min_fan_speed = 100
min_print_speed = 25
slowdown_below_layer_time = 8
start_filament_gcode = "; Filament gcode\nM572 D0 S0.07\nM572 D1 S0.07"
temperature = 215

[filament:PLA @E2 0.6n]
bed_temperature = 60
bridge_fan_speed = 100
compatible_printers = 
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_RAISE3D.*/ and printer_notes=~/.*PRINTER_MODEL_E2.*/ and nozzle_diameter[0]==0.6
compatible_prints = 
compatible_prints_condition = 
cooling = 1
disable_fan_first_layers = 1
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 60
filament_colour = #FF8000
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 30
filament_density = 1.24
filament_deretract_speed = nil
filament_diameter = 1.75
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 15
filament_minimal_purge_on_wipe_tower = 15
filament_notes = ""
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_speed = nil
filament_settings_id = ""
filament_soluble = 0
filament_spool_weight = 0
filament_toolchange_delay = 0
filament_type = PLA
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_vendor = (Unknown)
filament_wipe = nil
first_layer_bed_temperature = 60
first_layer_temperature = 220
full_fan_speed_layer = 0
inherits = 
max_fan_speed = 100
min_fan_speed = 100
min_print_speed = 25
slowdown_below_layer_time = 8
start_filament_gcode = "; Filament gcode\nM572 D0 S0.07\nM572 D1 S0.07"
temperature = 215

[filament:PVA @E2]
bed_temperature = 50
bridge_fan_speed = 100
compatible_printers = 
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_RAISE3D.*/ and printer_notes=~/.*PRINTER_MODEL_E2.*/ and nozzle_diameter[0]==0.4
compatible_prints = 
compatible_prints_condition = 
cooling = 0
disable_fan_first_layers = 3
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 60
filament_colour = #C0C0C0
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 50
filament_density = 1.23
filament_deretract_speed = nil
filament_diameter = 1.75
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 3.8
filament_minimal_purge_on_wipe_tower = 15
filament_notes = ""
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_speed = nil
filament_settings_id = ""
filament_soluble = 1
filament_spool_weight = 0
filament_toolchange_delay = 0
filament_type = PVA
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_vendor = (Unknown)
filament_wipe = nil
first_layer_bed_temperature = 50
first_layer_temperature = 215
full_fan_speed_layer = 0
inherits = 
max_fan_speed = 100
min_fan_speed = 35
min_print_speed = 10
slowdown_below_layer_time = 10
start_filament_gcode = "; Filament gcode\nM572 D0 S0.07\nM572 D1 S0.07"
temperature = 215

[filament:PVA @E2 0.6n]
bed_temperature = 50
bridge_fan_speed = 100
compatible_printers = 
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_RAISE3D.*/ and printer_notes=~/.*PRINTER_MODEL_E2.*/ and nozzle_diameter[0]==0.6
compatible_prints = 
compatible_prints_condition = 
cooling = 0
disable_fan_first_layers = 3
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
extrusion_multiplier = 1.1
fan_always_on = 0
fan_below_layer_time = 60
filament_colour = #C0C0C0
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 50
filament_density = 1.23
filament_deretract_speed = nil
filament_diameter = 1.75
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 3.8
filament_minimal_purge_on_wipe_tower = 15
filament_notes = ""
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_speed = nil
filament_settings_id = ""
filament_soluble = 1
filament_spool_weight = 0
filament_toolchange_delay = 0
filament_type = PVA
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_vendor = (Unknown)
filament_wipe = nil
first_layer_bed_temperature = 50
first_layer_temperature = 215
full_fan_speed_layer = 0
inherits = 
max_fan_speed = 100
min_fan_speed = 35
min_print_speed = 10
slowdown_below_layer_time = 10
start_filament_gcode = "; Filament gcode\nM572 D0 S0.07\nM572 D1 S0.07"
temperature = 215

[filament:WOOD @E2]
bed_temperature = 60
bridge_fan_speed = 100
compatible_printers = 
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_RAISE3D.*/ and printer_notes=~/.*PRINTER_MODEL_E2.*/ and nozzle_diameter[0]==0.4
compatible_prints = 
compatible_prints_condition = 
cooling = 1
disable_fan_first_layers = 1
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
extrusion_multiplier = 1.1
fan_always_on = 1
fan_below_layer_time = 100
filament_colour = #804000
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 50
filament_density = 1.58
filament_deretract_speed = nil
filament_diameter = 1.75
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 10
filament_minimal_purge_on_wipe_tower = 15
filament_notes = ""
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_lift = 0.2
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_speed = nil
filament_settings_id = ""
filament_soluble = 0
filament_spool_weight = 0
filament_toolchange_delay = 0
filament_type = WOOD
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_vendor = (Unknown)
filament_wipe = nil
first_layer_bed_temperature = 60
first_layer_temperature = 220
full_fan_speed_layer = 4
inherits = 
max_fan_speed = 100
min_fan_speed = 100
min_print_speed = 15
slowdown_below_layer_time = 15
start_filament_gcode = "; Filament gcode\nM572 D0 S0.07\nM572 D1 S0.07"
temperature = 220

[filament:WOOD @E2 0.6n]
bed_temperature = 60
bridge_fan_speed = 100
compatible_printers = 
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_RAISE3D.*/ and printer_notes=~/.*PRINTER_MODEL_E2.*/ and nozzle_diameter[0]==0.6
compatible_prints = 
compatible_prints_condition = 
cooling = 1
disable_fan_first_layers = 1
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
extrusion_multiplier = 1.2
fan_always_on = 1
fan_below_layer_time = 100
filament_colour = #804000
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 50
filament_density = 1.58
filament_deretract_speed = nil
filament_diameter = 1.75
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 10
filament_minimal_purge_on_wipe_tower = 15
filament_notes = ""
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_lift = 0.2
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_speed = nil
filament_settings_id = ""
filament_soluble = 0
filament_spool_weight = 0
filament_toolchange_delay = 0
filament_type = WOOD
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_vendor = (Unknown)
filament_wipe = nil
first_layer_bed_temperature = 60
first_layer_temperature = 220
full_fan_speed_layer = 4
inherits = 
max_fan_speed = 100
min_fan_speed = 100
min_print_speed = 15
slowdown_below_layer_time = 15
start_filament_gcode = "; Filament gcode\nM572 D0 S0.07\nM572 D1 S0.07"
temperature = 220

[printer:Raise3D E2 0.4 - Dual extrude]
bed_custom_model = 
bed_custom_texture = C:\\Users\\vegar\\AppData\\Roaming\\PrusaSlicer-beta\\physical_printer\\Overlay.svg
bed_shape = 30x0,325x0,325x240,30x240
before_layer_gcode = ;LAYER:[layer_num]
between_objects_gcode = 
color_change_gcode = M2000 ; pause/colorchange
cooling_tube_length = 5
cooling_tube_retraction = 91.5
default_filament_profile = ""
default_print_profile = 
deretract_speed = 0,0
end_gcode = M1002 ; Start of End G-code\nM605 S0 ; set to standard mode\nG92 E0 ; set position\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nM107 ; turn off fan\nG91\nG1 E-1 F1800 ; retract\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+2, max_print_height)}{endif} F720 ; Move print head up\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+30, max_print_height)}{endif} F720 ; Move print head further up\nG28 X0 Y0 ; move toolheads to start positions\nM84 ; stop idle hold\nG90 ; set to absolute positioning
extra_loading_move = -2
extruder_colour = ;#000000
extruder_offset = 0x0,35x0
gcode_flavor = marlin
high_current_on_filament_swap = 0
host_type = octoprint
inherits = 
layer_gcode = 
machine_limits_usage = time_estimate_only
machine_max_acceleration_e = 3000,5000
machine_max_acceleration_extruding = 800,1250
machine_max_acceleration_retracting = 1500,1250
machine_max_acceleration_x = 1000,1000
machine_max_acceleration_y = 500,1000
machine_max_acceleration_z = 100,200
machine_max_feedrate_e = 20,120
machine_max_feedrate_x = 100,200
machine_max_feedrate_y = 100,200
machine_max_feedrate_z = 5,12
machine_max_jerk_e = 5,2.5
machine_max_jerk_x = 8,10
machine_max_jerk_y = 5,10
machine_max_jerk_z = 0.4,0.4
machine_min_extruding_rate = 0,0
machine_min_travel_rate = 0,0
max_layer_height = 0.32,0.32
max_print_height = 240
min_layer_height = 0.1,0.1
nozzle_diameter = 0.4,0.4
parking_pos_retraction = 92
pause_print_gcode = M2000 ; pause/colorchange
print_host = 
printer_model = E2-Dual
printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_RAISE3D\nPRINTER_MODEL_E2\n
printer_settings_id = 
printer_technology = FFF
printer_variant = 
printer_vendor = 
printhost_apikey = 
printhost_cafile = 
remaining_times = 0
retract_before_travel = 0,0
retract_before_wipe = 0%,0%
retract_layer_change = 0,0
retract_length = 1,1
retract_length_toolchange = 2,2
retract_lift = 0.2,0.2
retract_lift_above = 0,0
retract_lift_below = 0,0
retract_restart_extra = 0,0
retract_restart_extra_toolchange = 0,0
retract_speed = 40,40
silent_mode = 0
single_extruder_multi_material = 0
start_gcode = M605 S0 ; set to standard mode\nG90 ; set printer absolute mode\nM82 ; set extruder to absolute mode\nM106 S0 ; fan off\nM140 S[first_layer_bed_temperature] ; set bed temp\nM104 S[first_layer_temperature] T0 ; set extruder temp\nM104 S[first_layer_temperature] T1; set extruder temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] T0 ; wait for extruder temp\nM109 S[first_layer_temperature] T1; wait for extruder temp\nG28 ; home all axes\nT0 ; set first toolhead\nG1 Z3 F500 ; Move to Z3 for height clearance before Intro line\nG92 E0 ; set position\n; intro line\nG1 Z0.35 F800 ;\nG1 X60 Y-2 F800 ;\nG1 X140 Y-2 E12 F200 ;\nG1 Z5 E15 F200 ; Move to Z5 to prevent dragging nozzle and scratching bed\nG92 E0 ; set position\nT1\nG92 E0 ; set position\nG1 X300 Y-2 F800\nG1 Z0.35 F200\nG1 X360 Y-2 E13 F200\nG1 E15 F200\nG1 Z5 F200\nG92 E0\nT0\nG1 F9000.0 ;\nM117 Printing...\nM1001 ; End of Start G-code
template_custom_gcode = 
thumbnails = 
toolchange_gcode = M104 S{temperature[0] * 0.85} T[current_extruder]; set extruder temp\nM104 S[temperature] T[next_extruder]; set extruder temp\nM109 S[temperature] T[next_extruder]; wait for extruder temp
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
variable_layer_height = 1
wipe = 0,0
z_offset = 0

[printer:Raise3D E2 0.4 - Duplicate]
bed_custom_model = 
bed_custom_texture = C:\\Users\\vegar\\AppData\\Roaming\\PrusaSlicer-beta\\physical_printer\\Overlay.svg
bed_shape = 0x0,165x0,165x240,0x240
before_layer_gcode = ;LAYER:[layer_num]
between_objects_gcode = 
color_change_gcode = M2000 ; pause/colorchange
cooling_tube_length = 5
cooling_tube_retraction = 91.5
default_filament_profile = ""
default_print_profile = 
deretract_speed = 0,0
end_gcode = M1002 ; Start of End G-code\nG1 E-1 F1800 ; retract\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nM106 S0 ; turn off fan\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+2, max_print_height)}{endif} F720 ; Move print head up\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+30, max_print_height)}{endif} F720 ; Move print head further up\nG28 X0 U0 ; move toolheads to start positions\nG1 Y240 ; Move bed to front and present print\nM84 ; Disable steppers\nM18 ; Disable stepper motors\nM605 S0 ; set to standard mode
extra_loading_move = -2
extruder_colour = ;
extruder_offset = 0x0,35x0
gcode_flavor = marlin
high_current_on_filament_swap = 0
host_type = octoprint
inherits = 
layer_gcode = 
machine_limits_usage = time_estimate_only
machine_max_acceleration_e = 3000,5000
machine_max_acceleration_extruding = 800,1250
machine_max_acceleration_retracting = 1500,1250
machine_max_acceleration_x = 1000,1000
machine_max_acceleration_y = 500,1000
machine_max_acceleration_z = 100,200
machine_max_feedrate_e = 20,120
machine_max_feedrate_x = 100,200
machine_max_feedrate_y = 100,200
machine_max_feedrate_z = 5,12
machine_max_jerk_e = 5,2.5
machine_max_jerk_x = 8,10
machine_max_jerk_y = 5,10
machine_max_jerk_z = 0.4,0.4
machine_min_extruding_rate = 0,0
machine_min_travel_rate = 0,0
max_layer_height = 0.32,0.32
max_print_height = 240
min_layer_height = 0.1,0.1
nozzle_diameter = 0.4,0.4
parking_pos_retraction = 92
pause_print_gcode = M2000 ; pause/colorchange
print_host = 
printer_model = E2-Duplicate
printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_RAISE3D\nPRINTER_MODEL_E2
printer_settings_id = 
printer_technology = FFF
printer_variant = 
printer_vendor = 
printhost_apikey = 
printhost_cafile = 
remaining_times = 0
retract_before_travel = 0,0
retract_before_wipe = 0%,0%
retract_layer_change = 0,0
retract_length = 1,1
retract_length_toolchange = 2,2
retract_lift = 0.2,0.2
retract_lift_above = 0,0
retract_lift_below = 0,0
retract_restart_extra = 0,0
retract_restart_extra_toolchange = 0,0
retract_speed = 40,40
silent_mode = 0
single_extruder_multi_material = 0
start_gcode = M605 S1 ; set to duplicate mode\nG90 ; set printer absolute mode\nM82 ; set extruder to absolute mode\nM106 S0 ; fan off\nM140 S[first_layer_bed_temperature] ; set bed temp\nM104 S[first_layer_temperature] ; set extruder temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 ; home all axes\nG1 Z3 F500 ; Move to Z3 for height clearance before Intro line\nG92 E0 ; set position\n; intro line\nG1 Z0.35 F800 ;\nG1 X60 Y-2 F800 ;\nG1 X140 Y-2 E12 F200 ;\nG1 Z5 E15 F200 ; Move to Z5 to prevent dragging nozzle and scratching bed\nG92 E0 ; set position\nG1 F9000.0 ;\nM117 Printing...\nM1001 ; End of Start G-code
template_custom_gcode = 
thumbnails = 
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
variable_layer_height = 1
wipe = 0,0
z_offset = 0

[printer:Raise3D E2 0.4 - Left head]
bed_custom_model = 
bed_custom_texture = C:\\Users\\vegar\\AppData\\Roaming\\PrusaSlicer-beta\\physical_printer\\Overlay.svg
bed_shape = 0x0,330x0,330x240,0x240
before_layer_gcode = ;LAYER:[layer_num]
between_objects_gcode = 
color_change_gcode = M2000 ; pause/colorchange
cooling_tube_length = 5
cooling_tube_retraction = 91.5
default_filament_profile = ""
default_print_profile = 
deretract_speed = 0
end_gcode = M1002 ; Start of End G-code\nG1 E-1 F1800 ; retract\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nM106 S0 ; turn off fan\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+2, max_print_height)}{endif} F720 ; Move print head up\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+30, max_print_height)}{endif} F720 ; Move print head further up\nG28 X0 U0 ; move toolheads to start positions\nG1 Y240 ; Move bed to front and present print\nM84 ; Disable steppers\nM18 ; Disable stepper motors\nM605 S0 ; set to standard mode
extra_loading_move = -2
extruder_colour = #FF8040
extruder_offset = 0x0
gcode_flavor = marlin
high_current_on_filament_swap = 0
host_type = octoprint
inherits = 
layer_gcode = 
machine_limits_usage = time_estimate_only
machine_max_acceleration_e = 3000,5000
machine_max_acceleration_extruding = 800,1250
machine_max_acceleration_retracting = 1500,1250
machine_max_acceleration_x = 1000,1000
machine_max_acceleration_y = 500,1000
machine_max_acceleration_z = 100,200
machine_max_feedrate_e = 20,120
machine_max_feedrate_x = 100,200
machine_max_feedrate_y = 100,200
machine_max_feedrate_z = 5,12
machine_max_jerk_e = 5,2.5
machine_max_jerk_x = 8,10
machine_max_jerk_y = 5,10
machine_max_jerk_z = 0.4,0.4
machine_min_extruding_rate = 0,0
machine_min_travel_rate = 0,0
max_layer_height = 0.32
max_print_height = 240
min_layer_height = 0.1
nozzle_diameter = 0.4
parking_pos_retraction = 92
pause_print_gcode = M2000 ; pause/colorchange
print_host = 
printer_model = E2-Left
printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_RAISE3D\nPRINTER_MODEL_E2\n
printer_settings_id = 
printer_technology = FFF
printer_variant = 
printer_vendor = 
printhost_apikey = 
printhost_cafile = 
remaining_times = 0
retract_before_travel = 0
retract_before_wipe = 0%
retract_layer_change = 0
retract_length = 1
retract_length_toolchange = 10
retract_lift = 0.2
retract_lift_above = 0
retract_lift_below = 240
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 40
silent_mode = 0
single_extruder_multi_material = 0
start_gcode = M605 S0 ; set to standard mode\nG90 ; set printer absolute mode\nM82 ; set extruder to absolute mode\nM106 S0 ; fan off\nM140 S[first_layer_bed_temperature] ; set bed temp\nM104 S[first_layer_temperature] T0 ; set extruder temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] T0 ; wait for extruder temp\nG28 ; home all axes\nT0 ; set first toolhead\nG1 Z3 F500 ; Move to Z3 for height clearance before Intro line\nG92 E0 ; set position\n; intro line\nG1 Z0.35 F800 ;\nG1 X60 Y-2 F800 ;\nG1 X140 Y-2 E12 F200 ;\nG1 Z5 E15 F200 ; Move to Z5 to prevent dragging nozzle and scratching bed\nG92 E0 ; set position\nG1 F9000.0 ;\nM117 Printing...\nM1001 ; End of Start G-code
template_custom_gcode = 
thumbnails = 
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
variable_layer_height = 1
wipe = 0
z_offset = 0

[printer:Raise3D E2 0.4 - Mirror]
bed_custom_model = 
bed_custom_texture = C:\\Users\\vegar\\AppData\\Roaming\\PrusaSlicer-beta\\physical_printer\\Overlay.svg
bed_shape = 0x0,165x0,165x240,0x240
before_layer_gcode = ;LAYER:[layer_num]
between_objects_gcode = 
color_change_gcode = M2000 ; pause/colorchange
cooling_tube_length = 5
cooling_tube_retraction = 91.5
default_filament_profile = ""
default_print_profile = 
deretract_speed = 0,0
end_gcode = M1002 ; Start of End G-code\nG1 E-1 F1800 ; retract\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nM106 S0 ; turn off fan\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+2, max_print_height)}{endif} F720 ; Move print head up\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+30, max_print_height)}{endif} F720 ; Move print head further up\nG28 X0 U0 ; move toolheads to start positions\nG1 Y240 ; Move bed to front and present print\nM84 ; Disable steppers\nM18 ; Disable stepper motors\nM605 S0 ; set to standard mode
extra_loading_move = -2
extruder_colour = ;
extruder_offset = 0x0,35x0
gcode_flavor = marlin
high_current_on_filament_swap = 0
host_type = octoprint
inherits = 
layer_gcode = 
machine_limits_usage = time_estimate_only
machine_max_acceleration_e = 3000,5000
machine_max_acceleration_extruding = 800,1250
machine_max_acceleration_retracting = 1500,1250
machine_max_acceleration_x = 1000,1000
machine_max_acceleration_y = 500,1000
machine_max_acceleration_z = 100,200
machine_max_feedrate_e = 20,120
machine_max_feedrate_x = 100,200
machine_max_feedrate_y = 100,200
machine_max_feedrate_z = 5,12
machine_max_jerk_e = 5,2.5
machine_max_jerk_x = 8,10
machine_max_jerk_y = 5,10
machine_max_jerk_z = 0.4,0.4
machine_min_extruding_rate = 0,0
machine_min_travel_rate = 0,0
max_layer_height = 0.32,0.32
max_print_height = 240
min_layer_height = 0.1,0.1
nozzle_diameter = 0.4,0.4
parking_pos_retraction = 92
pause_print_gcode = M2000 ; pause/colorchange
print_host = 
printer_model = E2-Mirror
printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_RAISE3D\nPRINTER_MODEL_E2\n
printer_settings_id = 
printer_technology = FFF
printer_variant = 
printer_vendor = 
printhost_apikey = 
printhost_cafile = 
remaining_times = 0
retract_before_travel = 0,0
retract_before_wipe = 0%,0%
retract_layer_change = 0,0
retract_length = 1,1
retract_length_toolchange = 2,2
retract_lift = 0.2,0.2
retract_lift_above = 0,0
retract_lift_below = 0,0
retract_restart_extra = 0,0
retract_restart_extra_toolchange = 0,0
retract_speed = 40,40
silent_mode = 0
single_extruder_multi_material = 0
start_gcode = M605 S2 ; set to mirror mode\nG90 ; set printer absolute mode\nM82 ; set extruder to absolute mode\nM106 S0 ; fan off\nM140 S[first_layer_bed_temperature] ; set bed temp\nM104 S[first_layer_temperature] ; set extruder temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 ; home all axes\nG1 Z3 F500 ; Move to Z3 for height clearance before Intro line\nG92 E0 ; set position\n; intro line\nG1 Z0.35 F800 ;\nG1 X60 Y-2 F800 ;\nG1 X140 Y-2 E12 F200 ;\nG1 Z5 E15 F200 ; Move to Z5 to prevent dragging nozzle and scratching bed\nG92 E0 ; set position\nG1 F9000.0 ;\nM117 Printing...\nM1001 ; End of Start G-code
template_custom_gcode = 
thumbnails = 
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
variable_layer_height = 1
wipe = 0,0
z_offset = 0

[printer:Raise3D E2 0.4 - Right head]
bed_custom_model = 
bed_custom_texture = C:\\Users\\vegar\\AppData\\Roaming\\PrusaSlicer-beta\\physical_printer\\Overlay.svg
bed_shape = 35x0,365x0,365x240,35x240
before_layer_gcode = ;LAYER:[layer_num]
between_objects_gcode = 
color_change_gcode = M2000 ; pause/colorchange
cooling_tube_length = 5
cooling_tube_retraction = 91.5
default_filament_profile = ""
default_print_profile = 
deretract_speed = 0
end_gcode = M1002 ; Start of End G-code\nG1 E-1 F1800 ; retract\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nM106 S0 ; turn off fan\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+2, max_print_height)}{endif} F720 ; Move print head up\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+30, max_print_height)}{endif} F720 ; Move print head further up\nG28 X0 U0 ; move toolheads to start positions\nG1 Y240 ; Move bed to front and present print\nM84 ; Disable steppers\nM18 ; Disable stepper motors\nM605 S0 ; set to standard mode
extra_loading_move = -2
extruder_colour = #FF8040
extruder_offset = 0x0
gcode_flavor = marlin
high_current_on_filament_swap = 0
host_type = octoprint
inherits = 
layer_gcode = 
machine_limits_usage = time_estimate_only
machine_max_acceleration_e = 3000,5000
machine_max_acceleration_extruding = 800,1250
machine_max_acceleration_retracting = 1500,1250
machine_max_acceleration_x = 1000,1000
machine_max_acceleration_y = 500,1000
machine_max_acceleration_z = 100,200
machine_max_feedrate_e = 20,120
machine_max_feedrate_x = 100,200
machine_max_feedrate_y = 100,200
machine_max_feedrate_z = 5,12
machine_max_jerk_e = 5,2.5
machine_max_jerk_x = 8,10
machine_max_jerk_y = 5,10
machine_max_jerk_z = 0.4,0.4
machine_min_extruding_rate = 0,0
machine_min_travel_rate = 0,0
max_layer_height = 0.32
max_print_height = 240
min_layer_height = 0.1
nozzle_diameter = 0.4
parking_pos_retraction = 92
pause_print_gcode = M2000 ; pause/colorchange
print_host = 
printer_model = E2-Right
printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_RAISE3D\nPRINTER_MODEL_E2\n
printer_settings_id = 
printer_technology = FFF
printer_variant = 
printer_vendor = 
printhost_apikey = 
printhost_cafile = 
remaining_times = 0
retract_before_travel = 0
retract_before_wipe = 0%
retract_layer_change = 0
retract_length = 1
retract_length_toolchange = 10
retract_lift = 0.2
retract_lift_above = 0
retract_lift_below = 240
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 40
silent_mode = 0
single_extruder_multi_material = 0
start_gcode = M605 S0 ; set to standard mode\nG90 ; set printer absolute mode\nM82 ; set extruder to absolute mode\nM106 S0 ; fan off\nM140 S[first_layer_bed_temperature] ; set bed temp\nM104 S[first_layer_temperature] T1 ; set extruder temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] T1 ; wait for extruder temp\nG28 ; home all axes\nT1 ; set second toolhead\nG1 Z3 F500 ; Move to Z3 for height clearance before Intro line\nG92 E0 ; set position\n; intro line\nG1 Z0.35 F800 ;\nG1 X60 Y-2 F800 ;\nG1 X140 Y-2 E12 F200 ;\nG1 Z5 E15 F200 ; Move to Z5 to prevent dragging nozzle and scratching bed\nG92 E0 ; set position\nG1 F9000.0 ;\nM117 Printing...\nM1001 ; End of Start G-code
template_custom_gcode = 
thumbnails = 
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
variable_layer_height = 1
wipe = 0
z_offset = 0

[printer:Raise3D E2 0.6 - Dual extrude]
bed_custom_model = 
bed_custom_texture = C:\\Users\\vegar\\AppData\\Roaming\\PrusaSlicer-beta\\physical_printer\\Overlay.svg
bed_shape = 30x0,325x0,325x240,30x240
before_layer_gcode = ;LAYER:[layer_num]
between_objects_gcode = 
color_change_gcode = M2000 ; pause/colorchange
cooling_tube_length = 5
cooling_tube_retraction = 91.5
default_filament_profile = ""
default_print_profile = 
deretract_speed = 0,0
end_gcode = M1002 ; Start of End G-code\nG1 E-1 F1800 ; retract\nM221 T0 S100 ; reset flow\nM221 T1 S100 ; reset flow\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nM106 S0 ; turn off fan\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+2, max_print_height)}{endif} F720 ; Move print head up\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+30, max_print_height)}{endif} F720 ; Move print head further up\nG28 X0 U0 ; move toolheads to start positions\nG1 Y240 ; Move bed to front and present print\nM84 ; Disable steppers\nM18 ; Disable stepper motors\nM605 S0 ; set to standard mode
extra_loading_move = -2
extruder_colour = ;#000000
extruder_offset = 0x0,0x0
gcode_flavor = marlin
high_current_on_filament_swap = 0
host_type = octoprint
inherits = 
layer_gcode = 
machine_limits_usage = time_estimate_only
machine_max_acceleration_e = 3000,5000
machine_max_acceleration_extruding = 800,1250
machine_max_acceleration_retracting = 1500,1250
machine_max_acceleration_x = 1000,1000
machine_max_acceleration_y = 500,1000
machine_max_acceleration_z = 100,200
machine_max_feedrate_e = 20,120
machine_max_feedrate_x = 100,200
machine_max_feedrate_y = 100,200
machine_max_feedrate_z = 5,12
machine_max_jerk_e = 5,2.5
machine_max_jerk_x = 8,10
machine_max_jerk_y = 5,10
machine_max_jerk_z = 0.4,0.4
machine_min_extruding_rate = 0,0
machine_min_travel_rate = 0,0
max_layer_height = 0.48,0.48
max_print_height = 240
min_layer_height = 0.15,0.15
nozzle_diameter = 0.6,0.6
parking_pos_retraction = 92
pause_print_gcode = M2000 ; pause/colorchange
print_host = 
printer_model = E2-Dual
printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_RAISE3D\nPRINTER_MODEL_E2\n
printer_settings_id = 
printer_technology = FFF
printer_variant = 
printer_vendor = 
printhost_apikey = 
printhost_cafile = 
remaining_times = 0
retract_before_travel = 0,0
retract_before_wipe = 0%,0%
retract_layer_change = 0,0
retract_length = 0.6,0.6
retract_length_toolchange = 1,1
retract_lift = 0.2,0.2
retract_lift_above = 0,0
retract_lift_below = 0,0
retract_restart_extra = 0,0
retract_restart_extra_toolchange = 0,0
retract_speed = 40,40
silent_mode = 0
single_extruder_multi_material = 0
start_gcode = M605 S0 ; set to standard mode\nM221 S96 ; set flow rate\nG90 ; set printer absolute mode\nM82 ; set extruder to absolute mode\nM106 S0 ; fan off\nM140 S[first_layer_bed_temperature] ; set bed temp\nM104 S[first_layer_temperature] T0 ; set extruder temp\nM104 S[first_layer_temperature] T1; set extruder temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] T0 ; wait for extruder temp\nM109 S[first_layer_temperature] T1; wait for extruder temp\nG28 ; home all axes\nT0 ; set first toolhead\nG1 Z3 F500 ; Move to Z3 for height clearance before Intro line\nG92 E0 ; set position\n; intro line\nG1 Z0.35 F800 ;\nG1 X60 Y-2 F800 ;\nG1 X140 Y-2 E12 F200 ;\nG1 Z5 E15 F200 ; Move to Z5 to prevent dragging nozzle and scratching bed\nG92 E0 ; set position\nT1\nG92 E0 ; set position\nG1 X300 Y-2 F800\nG1 Z0.35 F200\nG1 X360 Y-2 E13 F200\nG1 E15 F200\nG1 Z5 F200\nG92 E0\nT0\nG1 F9000.0 ;\nM117 Printing...\nM1001 ; End of Start G-code
template_custom_gcode = 
thumbnails = 
toolchange_gcode = M104 S{temperature[0] * 0.85} T[current_extruder]; set extruder temp\nM104 S[temperature] T[next_extruder]; set extruder temp\nM109 S[temperature] T[next_extruder]; wait for extruder temp
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
variable_layer_height = 1
wipe = 0,0
z_offset = 0

[printer:Raise3D E2 0.6 - Duplicate]
bed_custom_model = 
bed_custom_texture = C:\\Users\\vegar\\AppData\\Roaming\\PrusaSlicer-beta\\physical_printer\\Overlay.svg
bed_shape = 0x0,165x0,165x240,0x240
before_layer_gcode = ;LAYER:[layer_num]
between_objects_gcode = 
color_change_gcode = M2000 ; pause/colorchange
cooling_tube_length = 5
cooling_tube_retraction = 91.5
default_filament_profile = ""
default_print_profile = 
deretract_speed = 0,0
end_gcode = M1002 ; Start of End G-code\nG1 E-1 F1800 ; retract\nM221 T0 S100 ; reset flow\nM221 T1 S100 ; reset flow\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nM106 S0 ; turn off fan\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+2, max_print_height)}{endif} F720 ; Move print head up\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+30, max_print_height)}{endif} F720 ; Move print head further up\nG28 X0 U0 ; move toolheads to start positions\nG1 Y240 ; Move bed to front and present print\nM84 ; Disable steppers\nM18 ; Disable stepper motors\nM605 S0 ; set to standard mode
extra_loading_move = -2
extruder_colour = ;
extruder_offset = 0x0,35x0
gcode_flavor = marlin
high_current_on_filament_swap = 0
host_type = octoprint
inherits = 
layer_gcode = 
machine_limits_usage = time_estimate_only
machine_max_acceleration_e = 3000,5000
machine_max_acceleration_extruding = 800,1250
machine_max_acceleration_retracting = 1500,1250
machine_max_acceleration_x = 1000,1000
machine_max_acceleration_y = 500,1000
machine_max_acceleration_z = 100,200
machine_max_feedrate_e = 20,120
machine_max_feedrate_x = 100,200
machine_max_feedrate_y = 100,200
machine_max_feedrate_z = 5,12
machine_max_jerk_e = 5,2.5
machine_max_jerk_x = 8,10
machine_max_jerk_y = 5,10
machine_max_jerk_z = 0.4,0.4
machine_min_extruding_rate = 0,0
machine_min_travel_rate = 0,0
max_layer_height = 0.48,0.48
max_print_height = 240
min_layer_height = 0.15,0.15
nozzle_diameter = 0.6,0.6
parking_pos_retraction = 92
pause_print_gcode = M2000 ; pause/colorchange
print_host = 
printer_model = E2-Duplicate
printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_RAISE3D\nPRINTER_MODEL_E2
printer_settings_id = 
printer_technology = FFF
printer_variant = 
printer_vendor = 
printhost_apikey = 
printhost_cafile = 
remaining_times = 0
retract_before_travel = 0,0
retract_before_wipe = 0%,0%
retract_layer_change = 0,0
retract_length = 0.6,0.6
retract_length_toolchange = 1,1
retract_lift = 0.2,0.2
retract_lift_above = 0,0
retract_lift_below = 0,0
retract_restart_extra = 0,0
retract_restart_extra_toolchange = 0,0
retract_speed = 40,40
silent_mode = 0
single_extruder_multi_material = 0
start_gcode = M605 S1 ; set to duplicate mode\nM221 S96 ; set flow rate\nG90 ; set printer absolute mode\nM82 ; set extruder to absolute mode\nM106 S0 ; fan off\nM140 S[first_layer_bed_temperature] ; set bed temp\nM104 S[first_layer_temperature] ; set extruder temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 ; home all axes\nG1 Z3 F500 ; Move to Z3 for height clearance before Intro line\nG92 E0 ; set position\n; intro line\nG1 Z0.35 F800 ;\nG1 X60 Y-2 F800 ;\nG1 X140 Y-2 E12 F200 ;\nG1 Z5 E15 F200 ; Move to Z5 to prevent dragging nozzle and scratching bed\nG92 E0 ; set position\nG1 F9000.0 ;\nM117 Printing...\nM1001 ; End of Start G-code
template_custom_gcode = 
thumbnails = 
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
variable_layer_height = 1
wipe = 0,0
z_offset = 0

[printer:Raise3D E2 0.6 - Left head]
bed_custom_model = 
bed_custom_texture = C:\\Users\\vegar\\AppData\\Roaming\\PrusaSlicer-beta\\physical_printer\\Overlay.svg
bed_shape = 0x0,330x0,330x240,0x240
before_layer_gcode = ;LAYER:[layer_num]
between_objects_gcode = 
color_change_gcode = M2000 ; pause/colorchange
cooling_tube_length = 5
cooling_tube_retraction = 91.5
default_filament_profile = ""
default_print_profile = 
deretract_speed = 0
end_gcode = M1002 ; Start of End G-code\nG1 E-1 F1800 ; retract\nM221 T0 S100 ; reset flow\nM221 T1 S100 ; reset flow\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nM106 S0 ; turn off fan\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+2, max_print_height)}{endif} F720 ; Move print head up\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+30, max_print_height)}{endif} F720 ; Move print head further up\nG28 X0 U0 ; move toolheads to start positions\nG1 Y240 ; Move bed to front and present print\nM84 ; Disable steppers\nM18 ; Disable stepper motors\nM605 S0 ; set to standard mode
extra_loading_move = -2
extruder_colour = #FF8040
extruder_offset = 0x0
gcode_flavor = marlin
high_current_on_filament_swap = 0
host_type = octoprint
inherits = 
layer_gcode = 
machine_limits_usage = time_estimate_only
machine_max_acceleration_e = 3000,5000
machine_max_acceleration_extruding = 800,1250
machine_max_acceleration_retracting = 1500,1250
machine_max_acceleration_x = 1000,1000
machine_max_acceleration_y = 500,1000
machine_max_acceleration_z = 100,200
machine_max_feedrate_e = 20,120
machine_max_feedrate_x = 100,200
machine_max_feedrate_y = 100,200
machine_max_feedrate_z = 5,12
machine_max_jerk_e = 5,2.5
machine_max_jerk_x = 8,10
machine_max_jerk_y = 5,10
machine_max_jerk_z = 0.4,0.4
machine_min_extruding_rate = 0,0
machine_min_travel_rate = 0,0
max_layer_height = 0.48
max_print_height = 240
min_layer_height = 0.15
nozzle_diameter = 0.6
parking_pos_retraction = 92
pause_print_gcode = M2000 ; pause/colorchange
print_host = 
printer_model = E2-Left
printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_RAISE3D\nPRINTER_MODEL_E2\n
printer_settings_id = 
printer_technology = FFF
printer_variant = 
printer_vendor = 
printhost_apikey = 
printhost_cafile = 
remaining_times = 0
retract_before_travel = 0
retract_before_wipe = 0%
retract_layer_change = 0
retract_length = 0.6
retract_length_toolchange = 10
retract_lift = 0.2
retract_lift_above = 0
retract_lift_below = 240
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 40
silent_mode = 0
single_extruder_multi_material = 0
start_gcode = M605 S0 ; set to standard mode\nM221 T0 S96 ; set flow rate\nG90 ; set printer absolute mode\nM82 ; set extruder to absolute mode\nM106 S0 ; fan off\nM140 S[first_layer_bed_temperature] ; set bed temp\nM104 S[first_layer_temperature] T0 ; set extruder temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] T0 ; wait for extruder temp\nG28 ; home all axes\nT0 ; set first toolhead\nG1 Z3 F500 ; Move to Z3 for height clearance before Intro line\nG92 E0 ; set position\n; intro line\nG1 Z0.35 F800 ;\nG1 X60 Y-2 F800 ;\nG1 X140 Y-2 E12 F200 ;\nG1 Z5 E15 F200 ; Move to Z5 to prevent dragging nozzle and scratching bed\nG92 E0 ; set position\nG1 F9000.0 ;\nM117 Printing...\nM1001 ; End of Start G-code
template_custom_gcode = 
thumbnails = 
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
variable_layer_height = 1
wipe = 0
z_offset = 0

[printer:Raise3D E2 0.6 - Mirror]
bed_custom_model = 
bed_custom_texture = C:\\Users\\vegar\\AppData\\Roaming\\PrusaSlicer-beta\\physical_printer\\Overlay.svg
bed_shape = 0x0,165x0,165x240,0x240
before_layer_gcode = ;LAYER:[layer_num]
between_objects_gcode = 
color_change_gcode = M2000 ; pause/colorchange
cooling_tube_length = 5
cooling_tube_retraction = 91.5
default_filament_profile = ""
default_print_profile = 
deretract_speed = 0,0
end_gcode = M1002 ; Start of End G-code\nG1 E-1 F1800 ; retract\nM221 T0 S100 ; reset flow\nM221 T1 S100 ; reset flow\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nM106 S0 ; turn off fan\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+2, max_print_height)}{endif} F720 ; Move print head up\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+30, max_print_height)}{endif} F720 ; Move print head further up\nG28 X0 U0 ; move toolheads to start positions\nG1 Y240 ; Move bed to front and present print\nM84 ; Disable steppers\nM18 ; Disable stepper motors\nM605 S0 ; set to standard mode
extra_loading_move = -2
extruder_colour = ;
extruder_offset = 0x0,35x0
gcode_flavor = marlin
high_current_on_filament_swap = 0
host_type = octoprint
inherits = 
layer_gcode = 
machine_limits_usage = time_estimate_only
machine_max_acceleration_e = 3000,5000
machine_max_acceleration_extruding = 800,1250
machine_max_acceleration_retracting = 1500,1250
machine_max_acceleration_x = 1000,1000
machine_max_acceleration_y = 500,1000
machine_max_acceleration_z = 100,200
machine_max_feedrate_e = 20,120
machine_max_feedrate_x = 100,200
machine_max_feedrate_y = 100,200
machine_max_feedrate_z = 5,12
machine_max_jerk_e = 5,2.5
machine_max_jerk_x = 8,10
machine_max_jerk_y = 5,10
machine_max_jerk_z = 0.4,0.4
machine_min_extruding_rate = 0,0
machine_min_travel_rate = 0,0
max_layer_height = 0.48,0.48
max_print_height = 240
min_layer_height = 0.15,0.15
nozzle_diameter = 0.6,0.6
parking_pos_retraction = 92
pause_print_gcode = M2000 ; pause/colorchange
print_host = 
printer_model = E2-Mirror
printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_RAISE3D\nPRINTER_MODEL_E2\n
printer_settings_id = 
printer_technology = FFF
printer_variant = 
printer_vendor = 
printhost_apikey = 
printhost_cafile = 
remaining_times = 0
retract_before_travel = 0,0
retract_before_wipe = 0%,0%
retract_layer_change = 0,0
retract_length = 0.6,0.6
retract_length_toolchange = 1,1
retract_lift = 0.2,0.2
retract_lift_above = 0,0
retract_lift_below = 0,0
retract_restart_extra = 0,0
retract_restart_extra_toolchange = 0,0
retract_speed = 40,40
silent_mode = 0
single_extruder_multi_material = 0
start_gcode = M605 S2 ; set to mirror mode\nM221 S96 ; set flow rate\nG90 ; set printer absolute mode\nM82 ; set extruder to absolute mode\nM106 S0 ; fan off\nM140 S[first_layer_bed_temperature] ; set bed temp\nM104 S[first_layer_temperature] ; set extruder temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 ; home all axes\nG1 Z3 F500 ; Move to Z3 for height clearance before Intro line\nG92 E0 ; set position\n; intro line\nG1 Z0.35 F800 ;\nG1 X60 Y-2 F800 ;\nG1 X140 Y-2 E12 F200 ;\nG1 Z5 E15 F200 ; Move to Z5 to prevent dragging nozzle and scratching bed\nG92 E0 ; set position\nG1 F9000.0 ;\nM117 Printing...\nM1001 ; End of Start G-code
template_custom_gcode = 
thumbnails = 
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
variable_layer_height = 1
wipe = 0,0
z_offset = 0

[printer:Raise3D E2 0.6 - Right head]
bed_custom_model = 
bed_custom_texture = C:\\Users\\vegar\\AppData\\Roaming\\PrusaSlicer-beta\\physical_printer\\Overlay.svg
bed_shape = 35x0,365x0,365x240,35x240
before_layer_gcode = ;LAYER:[layer_num]
between_objects_gcode = 
color_change_gcode = M2000 ; pause/colorchange
cooling_tube_length = 5
cooling_tube_retraction = 91.5
default_filament_profile = ""
default_print_profile = 
deretract_speed = 0
end_gcode = M1002 ; Start of End G-code\nG1 E-1 F1800 ; retract\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nM106 S0 ; turn off fan\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+2, max_print_height)}{endif} F720 ; Move print head up\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+30, max_print_height)}{endif} F720 ; Move print head further up\nG28 X0 U0 ; move toolheads to start positions\nG1 Y240 ; Move bed to front and present print\nM84 ; Disable steppers\nM18 ; Disable stepper motors\nM605 S0 ; set to standard mode
extra_loading_move = -2
extruder_colour = #FF8040
extruder_offset = 0x0
gcode_flavor = marlin
high_current_on_filament_swap = 0
host_type = octoprint
inherits = 
layer_gcode = 
machine_limits_usage = time_estimate_only
machine_max_acceleration_e = 3000,5000
machine_max_acceleration_extruding = 800,1250
machine_max_acceleration_retracting = 3000,1250
machine_max_acceleration_x = 1000,1000
machine_max_acceleration_y = 500,1000
machine_max_acceleration_z = 100,200
machine_max_feedrate_e = 20,120
machine_max_feedrate_x = 100,200
machine_max_feedrate_y = 100,200
machine_max_feedrate_z = 5,12
machine_max_jerk_e = 5,2.5
machine_max_jerk_x = 8,10
machine_max_jerk_y = 5,10
machine_max_jerk_z = 0.4,0.4
machine_min_extruding_rate = 0,0
machine_min_travel_rate = 0,0
max_layer_height = 0.48
max_print_height = 240
min_layer_height = 0.15
nozzle_diameter = 0.6
parking_pos_retraction = 92
pause_print_gcode = M2000 ; pause/colorchange
print_host = 
printer_model = E2-Right
printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_RAISE3D\nPRINTER_MODEL_E2\n
printer_settings_id = 
printer_technology = FFF
printer_variant = 
printer_vendor = 
printhost_apikey = 
printhost_cafile = 
remaining_times = 0
retract_before_travel = 0
retract_before_wipe = 0%
retract_layer_change = 0
retract_length = 0.6
retract_length_toolchange = 10
retract_lift = 0.2
retract_lift_above = 0
retract_lift_below = 240
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 40
silent_mode = 0
single_extruder_multi_material = 0
start_gcode = M605 S0 ; set to standard mode\nG90 ; set printer absolute mode\nM82 ; set extruder to absolute mode\nM106 S0 ; fan off\nM140 S[first_layer_bed_temperature] ; set bed temp\nM104 S[first_layer_temperature] T1 ; set extruder temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] T1 ; wait for extruder temp\nG28 ; home all axes\nT1 ; set second toolhead\nG1 Z3 F500 ; Move to Z3 for height clearance before Intro line\nG92 E0 ; set position\n; intro line\nG1 Z0.35 F800 ;\nG1 X60 Y-2 F800 ;\nG1 X140 Y-2 E12 F200 ;\nG1 Z5 E15 F200 ; Move to Z5 to prevent dragging nozzle and scratching bed\nG92 E0 ; set position\nG1 F9000.0 ;\nM117 Printing...\nM1001 ; End of Start G-code
template_custom_gcode = 
thumbnails = 
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
variable_layer_height = 1
wipe = 0
z_offset = 0

[presets]
print = 0.20mm @E2 0.6
sla_print = 
sla_material = 
printer = Raise3D E2 0.6 - Right head
filament = PLA @E2 0.6n
physical_printer =